Managed Switches

NETGEAR Managed Switch Series, including M4250, M4300, M4350, M4500, and our legacy lines M4100, M4200, M5300, M6100, and M7100.

NETGEAR is aware of a growing number of phone and online scams. To learn how to stay safe click here.

Forum Widgets

Discussions

M7100-24x Cannot get ACLs to work
I have diligently tried to get the ACLs to work on my M7100-24x. Unfortunately both Standard and Extended ACLs do not work. I set the ACLs up and with the permit parameter and with the correct mask f...
kkuti
Jun 13, 2025 Place Managed Switches
ACL
24Views
0likes
0Comments
M4300-16x loses connection to Modem/Router
Hi, Looking for help regarding an issue where my managed switch will lose connection to the internet. And is fixed by unplug/plug the ethernet cable and generally will be ok for a few hours o...
givemeusername
Jun 11, 2025 Place Managed Switches
managed switches
5Views
0likes
0Comments
prevent NDI stream discovery
How would I prevent discovery of NDI streams going through an m4300 switch by other clients on the switch? Thanks
nigelgourley1
Jun 11, 2025 Place Managed Switches
managed switches
16Views
0likes
1Comment
M5300-52g slow start up when using v11 firmware
Hi During a deployment of a stack to replace an existing one, I ran into a problem. Instead of lift and shift of both units, the 52 port switch running v11 firmware (pre configured) was plugg...
ChrisPBacon1976
Jun 06, 2025 Place Managed Switches
Firmware Update
Installation
M5300
managed switches
troubleshoting
9Views
0likes
0Comments
M4350-12X12F SNMP v3 traps configuration
How to configure SNMP v3 Traps on this switch? I have current snmp config: snmp-server sysname "CENSORED-SYSNAME" ! snmp-server user "zabbix-netgear" DefaultWrite auth-sha512-key CENSORED-AUTHKE...
kuflowe_mocne
Jun 03, 2025 Place Managed Switches
M4300-12X12F
SNMP
snmp config
32Views
0likes
1Comment
M4300-12X12F unstable on 12.0.19.x
We have approximately 15 Netgear M4300 stacks where we hit a problem upgrading firmware. We've subsequently paused updating the others. The following stacks upgraded without problem and remain st...
bbs2web
May 25, 2025 Place Managed Switches
Firmware Update
managed switches
25Views
0likes
3Comments
I am trying to configure BGP on GSM4328
I am trying to configure BGP on GSM4328
syadu
May 20, 2025 Place Managed Switches
Installation
24Views
0likes
1Comment
Cannot ping Router WAN port from NetGear Switch
Hi, Everyone, I have a managed NetGear Switch M4350. The set up is easy, as follows. Host PC 10.10.10.9, there is only one VLAN on switch (10.10.10.1), and every port is its member. Router i...
Solved
spaceSlug
May 15, 2025 Place Managed Switches
managed switches
Router
43Views
0likes
3Comments
Dynamic RAM in GSM4352V1
I have a switch with serial 7FX13C5SA0330. I want to know the amount of dynamic ram (DRAM) that is available in the switch. I tried the checking the switch but it only shows CPU RAM which is just...
sahas1
May 13, 2025 Place Managed Switches
managed switches
35Views
0likes
3Comments
Need LOV for M4100-26G Network Switch
Subject says it all. Thanks
Randall_
May 12, 2025 Place Managed Switches
managed switches
24Views
0likes
1Comment

Knowledge Picks

What are the default user interface passwords for NETGEAR devices?

How do I reset a smart switch to factory default settings?

How do I access the admin page of my NETGEAR Web Managed Plus or Click Switch?

How to configure a VLAN on a NETGEAR managed switch?

Tags

Installation330 Topics
managed switches7 Topics
ACL3 Topics
Firmware Update2 Topics

NETGEAR Academy

Boost your skills with the Netgear Academy - Get trained, certified and stay ahead with the latest Netgear technology!

Join Us!

ProSupport for Business

Comprehensive support plans for maximum network uptime and business peace of mind.