NETGEAR is aware of a growing number of phone and online scams. To learn how to stay safe click here.
Forum Discussion
Orbi22W
I have a device (wireless grill controller) that uses a handoff from my phone (iOS 12.1) to join the network. The device is 2.4 Ghz capable only. Can I create a 2.4G only SSID? Alternatively, can I...
Orbi doesn't support seperate SSIDs.
Orbi connects devices to the most appropriate frequency based on device support. So if your device supports only 2.4ghz, it should connect to the 2.4Ghz radio of the Orbi.
Welp, here is step one of the controller’s setup process
1. If you have a dual band router, ensure you have separate network names, or SSIDs, for the 2.4 and 5.0 bands (aka 2.4 and 5.0Ghz signal, frequency, network, or radio). In order to reconnect the split networks later we want to rename the 5.0 signal and not the 2.4 signal. This allows reconsolidation without losing the grill from the WiFi network.
Can I temporarily disable the 5Ghz radio in the Orbi?
No. You can turn down the power output of the 5Ghz radio from 100% to say 25% and see if that helps.
Just curious, what is the purpose of this wireless grill device?
"Just curious, what is the purpose of this wireless grill device? "
Sorry for the long delay, thanks for your input on my issue.
The grill controller connects to my phone, shows me temperatures in the pit, and temperature outputs from 2 meat probles. More importantly it, allows me to startup/shutdown and adjust the temperature setpoint of my wood pellet smoker/grill.
The Grill IoT vendor (https://www.rectecgrills.com/wi-fi-set-up/) seems to be concerned that the mobile device with the App and the Grill controller are on the same radio (same band). Most discovery processes make use if IP broadcast or IGMP multicast - where a modern wireless device like the Orbi system can be considered transparent. Some buggy routers (this includes some Netgear units) are blocking IP broadcast or IGMP multicast 2.4GHz<->5GHz for example.
SilentService wrote:
.......Can I temporarily disable the 5Ghz radio in the Orbi?
This can probably help:
https://community.netgear.com/t5/Orbi/HOW-TO-DISABLE-5G-TEMPORARILY-ON-ORBI-ROUTER/m-p/1469365
Or the following summary steps:
1
Power off the satellites.
2
Go to:
3
Check "Enable Telnet"
4
Open the Terminal application on the MAC
5
nc orbilogin.com 23
6
Enter your Orbi router username (admin) and your password at the prompts. (admin/password is the default)
7
Paste the following in to disable 5G for a set amount of seconds. This is 300 for now (5 minutes).
seconds=300; x=0; while [ $x -lt $seconds ]; do ip link set down dev $(config get wl5g_NORMAL_AP); x=$(( x + 1 )); echo "down $x"; sleep 1; done
8
Use "Weather Connect" to pair your station. You have 5 minutes if you used the nc (telnet) command above.
9
Go to:
10
UnCheck "Enable Telnet"
11
Power on the satellites.
Rec Tec: Mesh networks represent their own Pandora's Box, but we've opened that box and found the outlandish patch for the mesh network conundrum. The first step to conquering this task is to find the edge of the signal from your mesh network. This entails walking away from the router until you lose connection to the network. Next, come back into range of the network and forget it from your saved networks. Now, while still on the fringe of the network, get just close enough to find the network and reconnect to it. While staying on the fringe of the network reconnect to the grill. At this point you should leave your phone in the fringe range and achieve a quick blink state from the LED on the grill. Back at your phone, on your mesh network, complete the WiFi Setup process.
