NETGEAR is aware of a growing number of phone and online scams. To learn how to stay safe click here.
Forum Discussion
RBR50 How to Dual Broadcast 2.4 and 5.0 GHZ
After 9 hours of reading posts and trying multiple differnt things i am at a loss. Please HELP.
I have a Sagecom Router (provided by ISP) that is Dual Band broadcasting network called Spectrum_...
I agree with the analysis above by CrimpOn.
Please note the folllowing:
- If you really have the Sagemcom F@st 5260 router (which does not have any modem inside) then I think that you can just eliminate it and -instead- connect the modem directly to Orbi, which will simplify your setup.
- Your Sagemcom router has routing capability which Orbi also has and this will cause you issues as was mentioned by CrimpOn
- Also the wifi networks from your Sagemcom router will interfere with Orbi's unless you manually select the channels that Sagemcom and Orbi operate on.
- If you decide to keep the Sagemcom router then you have two options:
- Keep Sagemcom as your router, switch of the wifi in that router and set Orbi in AP mode
- Set Sagemcom in bridged mode, passthrough mode or DMZ forwarding and keep Orbi in Router Mode.
I do have a Sagecom 5260.
when i access 192.168.1.1 it opens the Sagecom access. In this area it tells me my Orbi is 192.168.1.12
When I try to access this from a browser it comes back with this response:
"This site can’t be reached
192.168.1.12 took too long to respond."
Spectrum (formerly TWC) set up the modem and router originally. I added the Orbi and satalite to Extend my coverage.
It seems to be setup as Line in (wall jack) to Modem (Arris TM1602) to Router (Sagecom 5260) to Orbi RBR50.
Is the Orbi RBR50 a Router? Can the Orbi and Sagecom switch places? I also have a work phone (internet phone) that currently runs through the Sagecom. Will doing this make it so I can access the Orbi? And allow me to Broadcast in both 2.4 and 5.0 GHZ?
Sorry so many questions. Appreciate the help.
DecepticonR2D2 wrote:
.......
It seems to be setup as Line in (wall jack) to Modem (Arris TM1602) to Router (Sagecom 5260) to Orbi RBR50.
.......
I think you can easily just remove the Sagemcom and connect Orbi directly to the Arris modem
DecepticonR2D2 wrote:
.......
....... I also have a work phone (internet phone) that currently runs through the Sagecom. Will doing this make it so I can access the Orbi? And allow me to Broadcast in both 2.4 and 5.0 GHZ?
........
Yes, you can attach your internet phone to Orbi the same way as you did for the Sagemcom router. Is it a wired IP phone?
Yes, Orbi will be then your main router and broadcast both on 2.4 and 5 GHz.
My guess is that you cannot connect to the Orbi at 192.168.1.12 because the Orbi is in the default state of "Remote Management not enabled. To the Orbi, anything coming through the WAN port is "remote", i.e. on the Internet somewhere with all the evil people. If you connected to one of the LAN ports on the Orbi and did an "ipconfig /all", you would probably see that the Orbi (gateway) has an entirely different IP address on the LAN side.
About that phone. If your "work phone" is simply a Voice over IP phone that can be connected anywhere on the Internet, then for certain you can take out Spectrum's modem and use your own. My "land line" phone is from Spectrum and communicates over special frequency bands within the cable spectrum. If I remove Spectrum's modem/router, then I lose that phone service entirely. Actually, I have a different model of Ubee modem/router than most customers because I wanted (a) to keep the phone number I have had for 40 years, and (b) find the voice quality of mobile phones unpleasant. and inferior to a "land line."
i.e. Did they give you a box and say, "go home and install this", or are they paying for a phone line from Spectrum?
