NETGEAR is aware of a growing number of phone and online scams. To learn how to stay safe click here.

Forum Discussion

SeánB's avatar
SeánB
Aspirant
May 24, 2020

MR1100 primary 4G band problem with distant 4G+ site

I am in a rural part of Ireland where I pick up a 4G+ site quite far away with the help of an outdoor MIMO antenna.  The cell operates on bands 20, 3 and 1 and my previous LTE Cat 6 router worked fin...
SeánB's avatar
SeánB
Aspirant
May 31, 2020

Thanks for replying.  The device SKU printed at the bottom is MR1100-100EUS and the H/W is 1.0.

 

Since posting above, it received a firmware update, current version is NTG9X50C_12.06.12.00.  The issue remains in this verson.

 

My provider operates on bands 1, 3 and 20, which that cellular bands article shows this covers.  Due to my distance from the cell tower, I can use band 20 as the primary band (transmit & receive) and bands 1 and 3 for carrier aggregation (receive only). 

 

From further testing, the M1 seems to switch to band 1 or 3 when the RSRP of either band is around -108dBm or less negative.  As a crude workaround, I attached extension leads to the antenna leads to deliberately attenuate the signal.  It now stays on band 20 longer while still being able to use the (now very weak) signal on bands 1 and 3 for carrier aggregation. 

 

Even with the signal weakened, it still occasionally jumps to band 3 as the RSRP fluctuates up/down depending on the weather, in which case I have go into the web interface to toggle the mode between band 20 and 'LTE ALL' to restore Internet access.  It appears that the router is not detecting that the cell is not allowing it transmit to it on bands 1 or 3 and in turn getting stuck trying. 

  • W1lliam's avatar
    W1lliam
    Virtuoso
    Jun 04, 2020

    Possible improvement could be getting customized LTE antenna designed for B20 (below 1700MHz is fine), which can improve B20 signal quality then you probably can stay on B20 as main band. Plug into TS-9 ports should work.

    • JohnPeng's avatar
      JohnPeng
      NETGEAR Expert
      Jun 05, 2020

      I agreed with William. You may have to get a better external antenna or adjust your antenna location to see whether the device can pick up better signal on B20. It is just tracky location for the device to work on B1, B3 and B20.

      • SeánB's avatar
        SeánB
        Aspirant
        Jun 05, 2020

        I have a pair of 90cm (3ft) cross-polarised LOG periodic antennae that covers 700-900MHz, so gave this a trial run with a tripod.

         

        With the current 1.05m (3.5ft) large wideband LOG periodic antennae that covers 700-2700MHz, I get about -100dB on band 20, band 3 and 1.  I have clear line of sight with the distant mast across a bay as usually vegetation attenuates the higher frequency bands.

         

        With the 700-900MHz antennae on a tripod, I get about -90dB on band 20, -112dB on band 3 and -115dB on band 1.  The router didn't change from band 20 during the 30 minutes I had this temporary set up. 

         

        Carrier aggregation also works, although with 60-70% the speed I got with the wideband antennae due to bands 1 & 3 being attenuated by 12-15dB. 

         

        I presume being told to change my antennae means that this bug is not fixable, so will try swapping the antenna when I get a chance.