NETGEAR is aware of a growing number of phone and online scams. To learn how to stay safe click here.
Forum Discussion
Solved
RBR850 We can't find your Orbi
Today my internet connection suddenly dropped while I was working. Upon troubleshooting, I found that the Orbi app, and 192.168.1.1 from my PC, are both no longer working. The app says "We can't find...
**Updated 5/25/2022 at 12:00 PM Pacific Time
Hello Orbi Family!
Thank you all so very much for sharing your experience with us! As previously mentioned, based on the feedback we received after deploying the first patch to a select group of customers, we learned that we had an opportunity to improve the next interaction of the patch. I am happy to say we have tested this patch internally and start to roll it out to those of you who have already submitted your serial numbers. This group includes those that were in the first round so that your Device List and Armor services will be restored without any intervention on your side.
Update: If you've private messaged me and have not received a response, I promise I'm not ignoring you! đ As you can imagine, I have received quite a lot of messages. To ensure the patch is pushed out to as many of you as possible, I am focusing on grabbing the information and getting it in the hands that need it to push the update.
Update: We have begun to roll out this patch in a phased approach. Several of you should have received the patch overnight. You can check to see if you're system received the patch by going to http://orbilogin.net/debug.htm and confirming the SeAL value shows -2. If you are unable to access this page it means the router has not received the patch. If you've submitted your serial number to me on or before 6 PM last night 5/24/2022, please restart your system by unplugging it and plugging it back in and wait approximately 5 minutes after the router is fully restarted and check again. We have heard a second restart has proven more successful if the router was affected by this issue.
For more information please visit: NETGEAR is rolling out a fix for an issue affecting the Orbi RBK85x and RBK75x Series Mesh Systems.
Please note: the satellites do not need to be updated at this time and may show on a different firmware version. This is expected.
Please continue to add the results of your experience with this issue so we can look into this further if needed. If this is a new issue after being able to access the router settings please create a new topic for better visibility. Thank you!
Best Regards to All,
Christine
Try accessing the RBRs web page at 192.168.1.1 using HTTP in MS Edge, FireFox or Opera.
Gdmann wrote:
Another observation I currently seen during this no access to the management interface, is it appears the RBR750 reboots every 12 hours now. This is seen when all devices drop network access and the white blinking ring is seen. Any one else seeing a similar behavior?
Yes but when I go to 192.168.1.1 I get my Verizon router not the Orbi
What is the IP address on a wired PC connected to the RBR?
Your ISP Modem already has a built in router and wifi. This would be a double NAT (two router) condition which isn't recommended. https://kb.netgear.com/30186/What-is-Double-NAT
https://kb.netgear.com/30187/How-to-fix-issues-with-Double-NAT
Couple of options,
1. Configure the modem for transparent bridge or modem only mode. Then use the Orbi router in router mode. You'll need to contact the ISP for help and information in regards to the modem being bridged correctly.
2. If you can't bridge the modem, disable ALL wifi radios on the modem, configure the modems DMZ/ExposedHost or IP Pass-Through for the IP address the Orbi router gets from the modem. Then you can use the Orbi router in Router mode.
3. Or disable all wifi radios on the modem and connect the Orbi router to the modem, configure AP mode on the Orbi router. https://kb.netgear.com/31218/How-do-I-configure-my-Orbi-router-to-act-as-an-access-point and https://www.youtube.com/watch?v=H7LOcJ8GdDo&app=desktop
https://kb.netgear.com/000061277/Which-features-are-disabled-on-my-Orbi-router-when-it-is-set-to-AP-ModeFor those who's Orbi's are under warranty, can they be returned for a new Orbi? If you have to do a factory reset and lose your config and if it still doesn't work then it seems simpler to just get a new one.
So I should just throw out my RBR 750 and buy a new one? Are you serious??????????????
I have wifi off on my FIOS router/modem but still have wifi
Hi, I'm having the same issue on this thread. I've decided to do factory reset. Question, do I disconnect all the cords except the power cord to the Orbi before hitting the reset button? Thanks
