NETGEAR is aware of a growing number of phone and online scams. To learn how to stay safe click here.
Forum Discussion
New - RBR850 / RBS850 Firmware Version v4.6.7.5 Released
No Release Notes at this time. I'll see if I can get some.
Download Link:
https://ntgr.my.salesforce.com/sfc/p/#300000000xsV/a/8b000000saFy/gnaaQgriSv_NWgvrN.dvn786cl4eG45R2.62LEI3edU
F...
Updated last night from 4.6.6.11 that had been rock solid. Did a dirty upgrade and did not power either router or Satelite off after upgrade.
Lost satelite and needed to reboot everything. It appears that the mesh is not working as well in this firmware. It has not picked up some of the nearest clients-
Everything else appears to be working correctly
This might be a regression: if I go to the control panel for each of the satellites by typing their IP addresses into a web browser, the satellite that is connected wirelessly displays "Unknown" for the name of each of its connected devices. The wired satellite displays the devices' names correctly. I've rebooted the wireless satellite and it's displaying the same behaviour.
Note that this doesn't seem to be affecting the operation of those devices, they are still connected and working correctly.
My other observation so far is devices seem more reluctant to connect to that specific wireless satellite than they were on 4.6.6.11. Might be just a temporary thing but there definitely seems to have been a change in behaviour there.
Both satellites and the main router have been updated to 4.6.7.5 and the system has been powered down and rebooted following the upgrade.
I had same issue after initial update. What I did was make sure everything was up and running and then did a power reboot via the Orbi app and when everything came back up, all devices showed up like they should.
OK, I just got mine installed. Did the grey install, installed FW, shut off RBS then RBR for 1 minute or more, then back ON with the RBR first and let it come to ready. The turned ON RBS one at a time. This time were going to be wireless with the RBS for a couple of days, then I'll connect them via ethernet. I set some IP address reservations for the RBS as well. Manual channels 1 and 40. CTS = 64. Transmit Power = 50%.
Basic Information
Firmware Version: V4.6.7.5_2.1.7dumaos: v3.0.410
seal: v2.1.5.21-0
seal_services: v2.1.5.9-0
armor-bd: v2.2.100.3
spc-circle: v3.25.0.2
CPU Load: 18.95%
Memory Usage(Used/Total): 305 MB/874 MB
System Uptime: 0 days 00:06:50
Will monitor this and see how it goes.
How do you see the cpu/memory etc information? I couldnt find those screens anywhere (except the attached devices one)
FURRYe38 wrote:OK, I just got mine installed. Did the grey install, installed FW, shut off RBS then RBR for 1 minute or more, then back ON with the RBR first and let it come to ready. The turned ON RBS one at a time. This time were going to be wireless with the RBS for a couple of days, then I'll connect them via ethernet. I set some IP address reservations for the RBS as well. Manual channels 1 and 40. CTS = 64. Transmit Power = 50%.
Basic Information
Firmware Version: V4.6.7.5_2.1.7dumaos: v3.0.410
seal: v2.1.5.21-0
seal_services: v2.1.5.9-0
armor-bd: v2.2.100.3
spc-circle: v3.25.0.2
CPU Load: 18.95%
Memory Usage(Used/Total): 305 MB/874 MB
System Uptime: 0 days 00:06:50
Will monitor this and see how it goes.
