NETGEAR is aware of a growing number of phone and online scams. To learn how to stay safe click here.
Forum Discussion
New - RBR850 / RBS850 Firmware Version v4.6.7.5 Released
No Release Notes at this time. I'll see if I can get some.
Download Link:
https://ntgr.my.salesforce.com/sfc/p/#300000000xsV/a/8b000000saFy/gnaaQgriSv_NWgvrN.dvn786cl4eG45R2.62LEI3edU
F...
SW_ wrote:
VerneArase wrote:
GoldenRetroGame wrote:
SW_ wrote:Just curious, have you tried using a new cable?
The cable is fine. The problem is only when connected to the Orbi when it starts to act up. It's 100% reproducable.
Yeah - typically the reason for degraded Ethernet link speed is often a result of link speed negotiation between the two nodes, bad switch, or the cable, which is acting up. If this were a result of bad FW, it would have been seen or reported by more people. In this case, If a reboot would restore the link speed and subsequently drop back down to 100Mbps, it could also be the client, bad port, or the cable. I had also encountered similar problem in the past, hence my curiosity. Since you've already confirmed it's not the cable, then it's something else other than bad FW. Otherwise, everyone would also be affected by the same problem.
ASUS is a good vendor and you can't go wrong with their router either. Good luck!
Well most people might not notive since Orbi doesn't have any linespeedindicators on the ethernet ports (curious btw). So the only way to know is by either testing or running it through some switch.
I have used a switch on mine and i have seen linkspeed drops to 100Mb.
They came and went and where part of the insabillity i experienced, and there are plenty of issues related to that.
So more people might have this issue but never realize they do.
That issue (actual network instabillity) and lots off IPv4 vs IPv6 issues where what made me decide to pull the plug.
You're right that not everyone would notice unless their Internet is not working. Given the number of posts on this FW thread, one would expect to see more people reporting this issue if it were the case. As you pointed out, there are other issues with this FW that inflicts pain on many people, myself included. The difference is our individual pain tolerant level before giving up. :smileyhappy:
By the way, Orbi displays WAN/LAN ports linkspeed on its start page if anyone wants to find out if they have the same issue or not. If it's a real issue and we have enough people reporting, perhaps NG might look into fixing it.
I would also presume there maybe a HW fault as well and not actually a FW issue. LAN cables and end point devices should be checked as well to help narrow down where the problem is actually at.
I can say for my 7 and 8 series, I have not seen this issue since day one when Orbi AX was installed. I would have seen this and also did due diligence to narrow down where the problem is pointing too.
I recommend for those that are seeing this, please make contact with NG support if you are seeing problems to let them know what your experiencing. They don't know whats happening if you don't let them know.
This FW version was a next step in getting some better stability for users that have already been having problems after v4 came out. From what I see and can tell it's is a step in the right direction however it's not perfect. It is WAY better than older versions IMO. NG is aware of everyones concerns about FW.
Good morning. I decided to return my Orbi. I've spent several hours with Netgear support, plus many more hours of my own time, trying to tweak settings and make other changes. After running an Asus XT8 system, which got almost identical numbers out of the gate without any adjustments, I decided that is the better solution for me. Plus, it's a little more affordable and allows me to add an additional node or two to cover hard-to-reach areas in my house.
FWIW, I didn't experience a difference between the released and beta firmware versions. Both performed the same, and I downloaded the beta at the advice of the Netgear support, when the root cause of my performance is likely signal interference, the layout of my house and network, and/or the nature of a mesh wifi solution (or some combination of all three).
Thanks for the dialogue, and I wish you success in getting your Orbi networks optimized. I am 99% sure that I'll stick with this Asus solution. Cheers!
Thanks for letting us know.
Good Luck.
I also suffers from regular unstablity onb some of the satellite for a few months while the configuration is unchanged and had been rock solid for a year or so. I didn't connect new devices. Not much has changed except maybe the IOS15 upgrade.
I wonder if the issue wouldn"'t be coming from saturation of third-party online services like the BidDefender armor: could it be that there is a limit at the level of the BitDefender servers in terms of capacity to screen URLs? I am asking because except for that oineline service one the route is afaik "independant".
