NETGEAR is aware of a growing number of phone and online scams. To learn how to stay safe click here.
Forum Discussion
Solved
New Online Update 4.6.3.16 (RBR850/RBS850)
Just did a downgrade from 4.6.3.9 to 3.2.18.1, factory resetted and I see Netgear are pushing an update automatically to 4.6.3.16. (see attached screenshot) This firmware is not available as an o...
FURRYe38 wrote:v3.2.11.2 was last version with telnet in the debug.htm UI.
jayeshm wrote:Thanks.
I will throw it up in my guest room and see how it holds up for a few days.
Just for checking, if one has to stick with a 3.xx firmware which one do you personally recommend?
Firstly thanks for all the help furry. You have been patiently helping everyone here, and while i was being sarcastic earlier, your help is much appreciated.
Using PFsense i threw up on an old nuc, i was able to block all updates and manually shift to 3.2.18xx which is the last v3 update. So far it seems to work. Taking your advice i reset them entirely, kept them off for half a day, and then plugged them back in and added them back. I think one of my satellites is a bit wonky, since it oddly loses connection once in a while, but the rest of them seem to be holding up fine.
I have been able to successfully block updates via pfsense, since whenever i check via firmware updates manually, it gives a connection error. I looked up all the names suggested here in the various threads and added all of them to a small blocklist.
After updating my RBK852 system to version V4.6.3.16_2.0.51 satellite wouldn't connect to router. Only after erasing satellite (2 times) and router I was able to sync both systems again.
I now face another problem: when the router is in "router mode" i can see 1 attached sattelite and N attached devices in the orbi web home page (right most tile) but as soon as I put the orbi in "AP mode" the attached satellite disapears from the home page (it is also invisible in firmware update page) but it is still visibile in the detailed attached devices page (the one where backhaul status quality is displayed).
I know that both pages do ajax requests and that requests to get_attached_devices result in:
{
"satellites": [
{
"mac": "XXXXXX",
"type": "Router",
"model": "RBS850",
"name": "Orbi Satellite-1",
"ip": "192.168.3.45",
"connectionType": "Wired",
"connectionImg": "img/wiredConnection.png",
"ConnectedOrbi": "Orbi Router",
"backhaulStatusStyle": "TextGreen",
"backhaulStatus": "Good",
"category": "0",
"status": 255,
"sat_type": 1,
"led_status": 0,
"led_brightness": 0,
"led_sync": 0,
"voice_reg": "",
"ConnectedOrbiMAC": "XXXXX"
}
],whereas requests done to basicstatus.cgi result in:
{
"internet": 0,
"internet_head": "STATUS",
"internet_text": "GOOD",
"satellites_num": 0,
"devices_num": 27
}Is this a webinterface glitch or does this cause problems with device not routing automatically between nodes?
I've tried changing wifi parameters in the router and after a few seconds those were synced to the satellite
What broswser are you using?
Has a full power OFF of the RBR and RBS for 1-2 minutes been performed then back ON with the RBR then RBS? Give about 4-5 minutes for the web page to update.
What host router are you using when in AP mode?
Should see similar on yours:
https://community.netgear.com/t5/Orbi-AX/New-V4-6-3-16/m-p/2140064/highlight/true#M19926
FURRYe38 wrote:What broswser are you using?
Has a full power OFF of the RBR and RBS for 1-2 minutes been performed then back ON with the RBR then RBS? Give about 4-5 minutes for the web page to update.
What host router are you using when in AP mode?
Should see similar on yours:
https://community.netgear.com/t5/Orbi-AX/New-V4-6-3-16/m-p/2140064/highlight/true#M19926
Browser: Safari on Mackbook Pro and Chrome on Pixel 5 but that doesn't mean anything because the pages reflect simply the variables they get from the ajax requests: "satellites_num": 0 from basicstatus.cgi etc.
Both satellite and router have been rebooted multiple times (keeping them off for more than x minutes) and the page even after waiting for 30 minutes is still the same.
Router when in AP mode: Vigor2865
What OSX version are you using on the mac?
I'll re-check mine as my captures were done on a Windows 10x64 PC and MS EDGE.
I have OSX 12 beta on my Mac Book Pro.
- Yes they did update it last night and jacked up both my systems too. Previously a month ago i had updated to version 4 manually (.6), and a lot of my sats became disconnected or poor. at that time i was able to manually load all my sats back to version 3 but not my router. Then everything worked great again. Now last night they forced everything to update again to (.16) and now they are all screwed. Im going to manually update my sats back to 3.18 and i bet they work again
