NETGEAR is aware of a growing number of phone and online scams. To learn how to stay safe click here.
Forum Discussion
Solved
New RBR850 / RBS850 Series Firmware Version v3.2.17.12 Released
New Features and Enhancements: Supports the new device notification feature Includes some security enhancements Security Fixes: Fixes security vulnerabilities. For more information about sec...
Thanks!
So I updated from v16 to 3.2.17. Finally for the first time since last FW update of August of 2020, I can now do a Speedtest from the Orbi app or router page. It only took 6 months for NG to fix the issue! Now I get intermittent drops throughout the day. Really frustrating. I updated my two RBS850s first then the RBR850. I’m ready to package it all up and send it to the CEO of NG with a description of the crap I’ve put up with after spending $1k on the system. Based on input from above I will go check that the 5GHZ channel is 40 or 48 and the. Do a reboot of all three devices and the modem, powering up the modem then the Router then the 2 Sattelite. If it doesn’t work they are either going on EBAY, the trash or to the CEO of NG.
So far, so good here after upgrading. It's been boringly working away since and no complaints from my IOT devices especially the NestCams that will let me know if the WiFi is flakey. So that's all good. I have it LAG connected to a CM1150V cablemodem for the WAN and on the LAN side, a GS116Ev2 switch. I finally put the Satellite back on the WiFi backhaul; not sure which is better, but it is theoretically faster than wired - either seems fine. All working well and snappy speeds.
I had been using an AC3000/RBK53 setup for a good while before and it was mostly solid too, but the AX30K is faster and a more responsive GUI too.
Thanks for the feedback. Glad it's working well for you. Mines been doing the same for a good while now.
Be sure to save off a back up configuration to file for safe keeping. Helps save time if a reset is needed.
Enjoy. :smileywink:
bullm00n wrote:So far, so good here after upgrading. It's been boringly working away since and no complaints from my IOT devices especially the NestCams that will let me know if the WiFi is flakey. So that's all good. I have it LAG connected to a CM1150V cablemodem for the WAN and on the LAN side, a GS116Ev2 switch. I finally put the Satellite back on the WiFi backhaul; not sure which is better, but it is theoretically faster than wired - either seems fine. All working well and snappy speeds.
I had been using an AC3000/RBK53 setup for a good while before and it was mostly solid too, but the AX30K is faster and a more responsive GUI too.
- So I updated my RBR850 and 2 RBS850s. Finally after 6 months the speed test is working again after the last firmware update killed that capability. Network now seems to be strong with one exception. Once or twice a day, the 5GHZ signal on one of my Sattelites will drop to zero for about 1 minute then come back up. Not a problem unless you are on zoom. I have NetSpot installed so I can see all of the signals (2.4 and 5 ghz) each from the router and 2 Sattelites ... 6 in all graphically displayed for each 10 seconds. Out of no where the 5 GHZ channel just drops and then Comes back. I’m in a rural area without any competing other LANS nearby. Any ideas?
Has a power off for 1 minute then back ON with the ISP modem and Orbi system been performed since last update?
Try swapping RBS locations with each other to see if the problem follows.
Might try a manual FW re-load of the RBS.
Try a factory reset and setup from scratch.
