NETGEAR is aware of a growing number of phone and online scams. To learn how to stay safe click here.
Forum Discussion
Orbi RBR850 + Orbi RBS850 Limited Connection due to DNS
Hi Community Experts I have had critical stability issues with my network (1 x RBR850 and 2 x RBS850 in a hardwired star configuration through 1GB network switch) since around january 2022. It wa...
What Firmware version is currently loaded?
What is the Mfr and model# of the Internet Service Providers modem/ONT the NG router is connected too?
Has a power off for 1 minute then back ON with the ISP modem and router been performed since last update?
Be sure to restart your network in this sequence:
Turn off and unplug modem.
Turn off router and computers.
Plug in and turn on modem. Wait 2 minutes for it to connect.
Turn on the router and wait 2 minutes for it to connect.
Turn on computers and rest of network.
What happens if you roll back to v4.6.3.9 now? I believe NG has turned off auto updates...
Firmware.
ISP Modem.
I will try to follow your guide, I have not done these steps after the last update. I hope it works and I will get back to you on this thread. However if not I will rollback to the old version and follow your guidelines for restart and cross my fingers that it will not override the firmware.
Of course it would be best to have the updates working 🙂
Thanks
Your ISP Modem already has a built in router and wifi. This would be a double NAT (two router) condition which isn't recommended. https://kb.netgear.com/30186/What-is-Double-NAT
https://kb.netgear.com/30187/How-to-fix-issues-with-Double-NAT
Couple of options,
1. Configure the modem for transparent bridge or modem only mode. Then use the Orbi router in router mode. You'll need to contact the ISP for help and information in regards to the modem being bridged correctly.
2. If you can't bridge the modem, disable ALL wifi radios on the modem, configure the modems DMZ/ExposedHost or IP Pass-Through for the IP address the Orbi router gets from the modem. Then you can use the Orbi router in Router mode.
3. Or disable all wifi radios on the modem and connect the Orbi router to the modem, configure AP mode on the Orbi router. https://kb.netgear.com/31218/How-do-I-configure-my-Orbi-router-to-act-as-an-access-point and https://www.youtube.com/watch?v=H7LOcJ8GdDo&app=desktopTry option #2 first...
Theres nothing past v4.6.8.2.
Thank you.
I have right from the start re-configured modem to bridge mode and later on changed to a fixed LAN setup with a switch connecting the Orbi Router and 2 x Satellites. It has been working fine for a year or so until around new year and from update v4.3.6.16 is my best guess.
I was testing your other guidelines, but it didn't do the trick. I have now rolled back firmware starting with satellites and ending with router as recommended to last workable firmware v4.3.6.9 for all Orbi units, but I faced problems with re-booting it kind of looped and didn't complete.
I then factory reset all Orbi units with v4.3.6.9 installed, unplugged all and started with the router which works fine now. I have som problems with the satellites which just cycle in a reboot state. I have now disconneced them and I will do the power reset close to the router and with no conncetion to the switch.
I am not yet complete with the process, but I will inform you the outcome here in this thread.
Hi againg
Firmware is overridden automatically to the below version for the router at least. I will try and stick with this version and make it work as good as it possibly can, but as I recall it and in my notes, issues began around this version upgrade. I do not expect to much. I kind of have the feeling of being stuck here, but apperantly I got to accept this and cross my fingers for an upgrade in the future that works. I can't see what I possibly can do to get this fixed sadly enough.
I will post here when I am back up and running with final comments!