NETGEAR is aware of a growing number of phone and online scams. To learn how to stay safe click here.
Forum Discussion
Solved
RBRE960 1GB Ports Power Cycling?
Hey all, just set up the RBRE960 router and two RBSE960 satellites. Initial stability was a little touch and go, but it seems to have calmed down and now it's pretty stable. I have my Orbi set up i...
Well, I was finally able to test this again. Disconnected all cables and then connected the Orbi 1GB router ports to my Netgear GS108v4 unmanaged switch. Tried all Orbi 1GB router ports and all 8 unmanaged switch ports, and I cannot duplicate the strange behavior from before. Now the two devices connect at 1GB speed and stay connected with the activity lights blinking constantly as expected. Not sure why it's different now, but I'm glad that it's now acting the way it's supposed to. Thank you for testing this setup, that took some effort and it's much appreciated.
What devices do you have connected to the 1Gb LAN ports?
What is the brand and model# of the host router the RBR is connected too on it's 10Gb WAN port in AP mode?
Did you configure Dynamic or Static IP addressing for AP mode? I prefer Static IP address.
What CAT# lan cable are you using between the RBR and wired devices? CAT6 UTP is recommended on the 1Gb ports, CAT6A STP for the 2.5 port and 10Gb WAN port.
What Firmware version is currently loaded?
F_V wrote:
Hey all, just set up the RBRE960 router and two RBSE960 satellites. Initial stability was a little touch and go, but it seems to have calmed down and now it's pretty stable. I have my Orbi set up in "AP Mode" with the modem connected to the yellow 10GB Internet port. There is one 2.5GB port to hardwire a satellite if desired, which I don't use. There are three 1GB ports, and my question is this. In AP Mode is it normal for these three 1GB ports to power cycle over and over? Any device I connect to these three ports will constantly connect and disconnect. Same with the 2.5GB port. My assumption is because it's in AP Mode and the Orbi only expects to see a modem/switch/firewall appliance connected to the 10GB Internet Port, but I just want to be sure before I'm out of the warranty period.
Thanks in advance!
This post can be closed. When I run the Orbi in AP Mode and plug the 3 1GB ports into an unmanaged switch, the port connection cycles on and off. Doesn't matter since I don't need to plug these ports into the switch, just wondering if anyone else had seen this behavior.
Are you plugging in all 3 LAN ports into the Switch or just one of the 3 LAN ports?
What is the brand and model of this LAN switch your using?
Do the RBS ethernet connect and sync correctly when directly connected to the back of the RBR using one of the 1 Gb LAN ports in back?
This is how it should be connected between the RBS and RBR:
https://kb.netgear.com/000051205/What-is-Ethernet-backhaul-and-how-do-I-set-it-up-on-my-Orbi-WiFi-System 📡
NG GS-105/108v4 and GS308v3, D-Link DGS-105/108 and HP ProCurve 1400/1800 series switches work for Orbi systems. XS505M and GS110MX work great with the 9 series.What devices do you have connected to the 1Gb LAN ports?
What is the brand and model# of the host router the RBR is connected too on it's 10Gb WAN port in AP mode?
Did you configure Dynamic or Static IP addressing for AP mode? I prefer Static IP address.
What CAT# lan cable are you using between the RBR and wired devices? CAT6 UTP is recommended on the 1Gb ports, CAT6A STP for the 2.5 port and 10Gb WAN port.
I've not seen with this my 9 series.
Post thread isn't closed since the problem hasn't been resolved.
I put my 9 series online yesterday with a D-Link DGS-105 switch with the RBR and two RBS connected to it using only the 1GB ports on the RBS and RBR.
I first let the RBS wirelessly sync after powering them ON. Then after BLUE was seen on the RBS, I plugged in the RBS ethernet cables one at a time.
Green cable is feed from RBR. 1st Purple cable is connected to one RBS. Yellow cable is connected to 2nd RBS. 2nd Purple cable is a wired PC.
Saw no issues with the ports cycling or disconnecting in any way. I had a Mac Book Pro ethernet connected behind one RBS and speed testing thru the RBS was successful and to spec.
Wow, when I posted that issue I didn't expect someone to recreate the setup and post results, thanks! So my issue is that when I plugged the Router 1GB ports into my unmanaged switch I could see the link power cycling/resetting about every 10 seconds or so by looking at the link/speed lights on the front of the switch. Since then I haven't had a need to plug my router into a switch using those ports, however I did try it again a few days ago and it was still doing this. Is your setup also in AP Mode like mine is?
Yes, I tested both AP and Router modes. AP mode was first since it was the last state I had my 9 series in.
Saw no power cycling issues at all.
I can only presume the switch your using maybe something causing this or at fault here.
F_V wrote:
This post can be closed. When I run the Orbi in AP Mode and plug the 3 1GB ports into an unmanaged switch, the port connection cycles on and off. Doesn't matter since I don't need to plug these ports into the switch, just wondering if anyone else had seen this behavior.
Please excuse my confusion. When I read this, my first impression was, "plugged ALL THREE gig ports into the same unmanaged switch???" That will never work. The first broadcast of any kind (ARP, DHCP, etc.) will cause a broadcast storm and the switch will disable the ports.
Yeah, now that I re-read my initial post I can see why you'd read it that way, my bad. No, just plugging a single 1GB Orbi port to a single port of an unmanaged switch.
