NETGEAR is aware of a growing number of phone and online scams. To learn how to stay safe click here.
Forum Discussion
RBS750 not connecting to RBR750
Hi all, First of all sorry if someone already posted this issue here but I was unable to find the exact same issue on my own. I bought a RBR750 with 2 RBS750 satellites, and managed to connec...
FURRYe38 wrote:What Firmware version is currently loaded?
The loaded SW is V4.6.5.14_2.0.54.
What is the Mfr and model# of the Internet Service Providers modem/ONT the NG router is connected too?
The modem is from SAGEMCOM and model is LIVEBOX 5 from Orange France.
thanks a lot in advance.
Joe
Does the RBS connect to the RBR if you ethernet connect it to the back of the RBR?
Does it get a IP address for the RBS seen on the RBRs web page?
Your ISP modem seems to have a built in router and wifi already. This would be a double NAT (two router) condition which isn't recommended. https://kb.netgear.com/30186/What-is-Double-NAT
https://kb.netgear.com/30187/How-to-fix-issues-with-Double-NAT
Couple of options,
1. Configure the modem for transparent bridge or modem only mode. Then use the Orbi router in router mode. You'll need to contact the ISP for help and information in regards to the modem being bridged correctly.
2. If you can't bridge the modem, disable ALL wifi radios on the modem, configure the modems DMZ/ExposedHost or IP Pass-Through for the IP address the Orbi router gets from the modem. Then you can use the Orbi router in Router mode.
3. Or disable all wifi radios on the modem and connect the Orbi router to the modem, configure AP mode on the Orbi router. https://kb.netgear.com/31218/How-do-I-configure-my-Orbi-router-to-act-as-an-access-point and https://www.youtube.com/watch?v=H7LOcJ8GdDo&app=desktop
FURRYe38 wrote:Does the RBS connect to the RBR if you ethernet connect it to the back of the RBR?
Unfortunately no... is does not connect and continue flashing white!
FURRYe38 wrote:Does it get a IP address for the RBS seen on the RBRs web page?
I have another satellite (I bought a pack of RBR + 2 RBS) connected to the router wirelessly and it does have an IP address.
FURRYe38 wrote:Your ISP modem seems to have a built in router and wifi already. This would be a double NAT (two router) condition which isn't recommended. https://kb.netgear.com/30186/What-is-Double-NAT
https://kb.netgear.com/30187/How-to-fix-issues-with-Double-NAT
Couple of options,
1. Configure the modem for transparent bridge or modem only mode. Then use the Orbi router in router mode. You'll need to contact the ISP for help and information in regards to the modem being bridged correctly.
2. If you can't bridge the modem, disable ALL wifi radios on the modem, configure the modems DMZ/ExposedHost or IP Pass-Through for the IP address the Orbi router gets from the modem. Then you can use the Orbi router in Router mode.
3. Or disable all wifi radios on the modem and connect the Orbi router to the modem, configure AP mode on the Orbi router. https://kb.netgear.com/31218/How-do-I-configure-my-Orbi-router-to-act-as-an-access-point and https://www.youtube.com/watch?v=H7LOcJ8GdDo&app=desktopI am not expert, but with my previous Orbi pack I never add an issue (only RBR + one RBS). This new one that I have today, also works fine with RBR and one RBS... I just don't get why can't I connect the second RBS and why it remains flashing white and nothing seems to make it stop.
thanks a lot for your help.
Best regards,
Joe
You can try updating the one working RBS first to v.2 FW then then the RBR lastly. then see if the 2nd RBS will ethernet connect to the RBR.
FURRYe38 wrote:You can try updating the one working RBS first to v.2 FW then then the RBR lastly. then see if the 2nd RBS will ethernet connect to the RBR.
OK, I have done the update, weirdly I can connect my deviced to the Orbi wifi, but cannot connect to the router via the web app, nore to the android app, says it is not finding the orbi network, while connected at it...