NETGEAR is aware of a growing number of phone and online scams. To learn how to stay safe click here.
Forum Discussion
Solved
New - RBR750 / RBS750 Firmware Version 4.6.5.14 Released
Enhancements:
Adds support for the RBS350
Security Fixes:
Fixes security vulnerabilities.
For more information about security vulnerabilities, visit https://www.netgear.com/about/secu...
WOW, this morning about 2am i decided to update my two ORBI RBS satillites first. and that went ok, till a fantom ORBI showed up in my Orbi App. i then proceeded to update the RBR750, that went well till it said it was online but it wasnt. i followed the directions according to Furrye38, (ty) and i unplugged the sats and then the router, waited 2-3 minutes then i plugged in the router and then the sats and waited........it took a few minutes and the router came online then the sats followed. it still took some time for all my devices to get back on line (about 60), which is normal thing that has been happening. then today was the test. we had some heavy thunderstorms roll in, these south florida storms alway knock out some power or damages some weak transformers to were the power goes on and off real quick. it happened 3 times in a half hour i also have the comcast modem and the RBR750 plugged into a surge and battery back up. the weakest like here is the sats, no battery-back up for them and they used to take forever to re-sync but after the upgraded firmware last night, WOW, the ORBI's came right back online which shocked me, i thought i would need to reboot the sats. but no input from me and the whole system came back online quick. i am no IT guy here but this is a major inprovement from the previous firmware that almost killed the ORBI system. thanks to all here on this forum, i have learned alot from here.
titaniumrx8 wrote:Others have asked what I will replace with but I am going to wait a while. Netgear has announced their 4 channel mesh so I would expect other manufacturers to do likewise and prices will eventually drop on the 3 channel products which are more than adequate for my needs. (Costco is now selling the RBK753 for $350 in case anyone wants to start over again)
NG can't get three channels right, I wouldn't hold my breath to see what they do with 4 channels. It's already a problem looking for an answer...
hetak1313 wrote:
titaniumrx8 wrote:Others have asked what I will replace with but I am going to wait a while. Netgear has announced their 4 channel mesh so I would expect other manufacturers to do likewise and prices will eventually drop on the 3 channel products which are more than adequate for my needs. (Costco is now selling the RBK753 for $350 in case anyone wants to start over again)
NG can't get three channels right, I wouldn't hold my breath to see what they do with 4 channels. It's already a problem looking for an answer...
The way I read it, titaniumrx8, is waiting for the 4 channel units to come out so the three channel units become cheaper. Given if NG comes out with 4 channel units, others will as well and THEIR 3 channel products will also become cheaper which is what he/she wants.
I think most people agree, though, NG is done - stay away and don't touch with a 10' pole so to speak.
- N3tworkDud3 wrote
"The way I read it, titaniumrx8, is waiting for the 4 channel units to come out so the three channel units become cheaper. Given if NG comes out with 4 channel units, others will as well and THEIR 3 channel products will also become cheaper which is what he/she wants.
I think most people agree, though, NG is done - stay away and don't touch with a 10' pole so to speak. "
Correct on all counts. Essentially waiting for 2.0 on these mesh systems. And it certainly won't be any Netgear product. Even if these firmware issues didn't occur, the whole concept of only 3 months support is the final nail. Netgear's competitors stand behind their products. I'm thankful that Costco took back my Orbi after 7 months. I've written to Costco to advise them that they should stop selling a product that can't satisfy their customers.
My next mesh system preferences:
Ability to install vpn directly onto the router.
Mixed mode WPA2/WPA3
Mixed mode for AX on all bands
4 lan ports on base station
Extensive settings customization via web interface
No mandatory monthly or annual fees
Guest network firewalled from network resources
Opt out or scheduled firmware updates
Turn off SSID broadcast
Good luck to everyone.
titaniumrx8 wrote:
My next mesh system preferences:
Ability to install vpn directly onto the router.
Mixed mode WPA2/WPA3
Mixed mode for AX on all bands
4 lan ports on base station
Extensive settings customization via web interface
No mandatory monthly or annual fees
Guest network firewalled from network resources
Opt out or scheduled firmware updates
Turn off SSID broadcast
Good luck to everyone.I believe you can do all that now with Ubiquiti/Edgerouter (the REAL Ubiquiti line - not the Alien et. al) along with their APs. Their stuff has really fine granular control of the entire network since their target market is the commercial market where security and control is of the utmost. If you're not used to it thought, there is a learning curve to their UI since there are so many controls/options.
The best part is because of their target market, they are really responsive to hardware/firmware issues (as far as I can tell). They also DON'T force updates, and you can roll back firmware anytime if needed/wanted.
Hi. Just want to tell my story. Maybe it will be helpful for somebody…
I bought RBR753 five months ago for switching to modern WiFi 6 Mesh system and get rid from my old WiFi system with several WiFi extenders. I did it based on a lot of positive reviews…
Then, I think as 80% of users here, I went to firmware related issues:
- I had connection interruptions for 10 seconds every 15-20 minutes (especially in Microsoft Teams and Zoom)
- I had this even on laptops connected directly to the RBR750 with WIRED connection type!
It was a nightmare given the fact that we all work from home now and have many meeting.
Returning to the old router immediately fixed all my issues.
I opened a support ticket but after two (!) months of communication with support team they did nothing, just asked me to wait for future firmware updates where they think it will be fixed.
After a month of fighting, I improved my networking knowledge a lot. Thank you Netgear for the education challenge. I understand in details now what is: Interfaces, TCP/UDP packets, NAT, Outbound NAT, Firewall rules, Port forwarding, Dynamic DNS, Unbound DNS, OpenVPN and WireGuard :-) I can configure all of them now!
So, I ended up with complete logical separation of my network. Now I have:
- router, which does routing, DHCP service, firewall and VPN only (Protectli FW6D with OPNsense OS and CoreBoot BIOS);
- switch (Linksys LGS116P) and I have wired all the devices I can, greatly expanding my existing home network;
- I switched the Orbi router (RBR750) to AP mode.
Both router (RBR750) and two satellites (RBS750) using the latest firmware
Both satellites (RBS750) are connected to the router USING CABLE for Backhaul (via my switch).It is the only working configuration for me. I do not have any interruptions now! WiFi Mesh is working fine in WiFi 6 (ax) mode.
So, if you are in the trap and cannot return Orbi then the only working configuration is: independent router + Orbi system in AP mode with satellites connected with cable for Backhaul.
I asked about some financial compensation from NetGear, because I spent a lot of additional unplanned money to buy a separate router, switch, CAT6 cables, ethernet outlets, plus I spent hours to my work for wiring the house. It was rejected by “Customer Care Advocate” :-)
I already talk out of buying any NetGear products several of my friends and colleagues.
I will never buy anything from NetGear myself.
End of my story. Thanks for reading.