RAX29 WiFi 6 Router not connecting at WiFi 6 with my laptop

Kitsap
Master
Jan 18, 2025
bardiferously wrote:
Apologies for being distracted (Squirrel).

So I circled back to this issue and found that my Guest network connects with AX, but my Main network connects still with AC.
Main
SSID: FiOS-D3Q0Z
Protocol: Wi-Fi 5 (802.11ac)
Security type: WPA3-Personal
Manufacturer: Intel Corporation
Description: Intel(R) Wi-Fi 6 AX201 160MHz
Driver version: 22.130.0.5
Network band (channel): 5 GHz (44)
Aggregated link speed (Receive/Transmit): 780/780 (Mbps)
Link-local IPv6 address: fe80::d6d5:a8f2:7c03:87d7%14
IPv6 default gateway: fe80::6ecd:d6ff:fe4b:bc85%14
IPv6 DNS servers: fe80::96a6:7eff:fe2f:9378%14 (Unencrypted)
IPv4 address: 10.0.0.20
IPv4 DNS servers: 10.0.0.1 (Unencrypted)
Physical address (MAC): 2C-8D-B1-A3-20-E6

Guest
SSID: Rajah-5G-Guest
Protocol: Wi-Fi 6 (802.11ax)
Security type: WPA3-Personal
Manufacturer: Intel Corporation
Description: Intel(R) Wi-Fi 6 AX201 160MHz
Driver version: 22.130.0.5
Network band (channel): 5 GHz (44)
Aggregated link speed (Receive/Transmit): 1201/1021 (Mbps)
Link-local IPv6 address: fe80::d6d5:a8f2:7c03:87d7%14
IPv6 default gateway: fe80::6ecd:d6ff:fe4b:bc85%14
IPv4 address: 10.0.0.20
IPv4 DNS servers: 10.0.0.1 (Unencrypted)
Physical address (MAC): 2C-8D-B1-A3-20-E6
It appears you have two different sources of Wi-Fi transmitting for your LAN.

Repeat question, look on the nameplate of the device.

What is the brand name and model number of the modem/ONT connected to the internet upstream of your RAX29?
- michaelkenward
  Guru - Experienced User
  Jan 18, 2025
  Kitsap wrote:
  
  bardiferously wrote:
  
  IPv4 address: 10.0.0.20
  IPv4 DNS servers: 10.0.0.1 (Unencrypted)
  Physical address (MAC): 2C-8D-B1-A3-20-E6
  
  It appears you have two different sources of Wi-Fi transmitting for your LAN.
  
  Repeat question, look on the nameplate of the device.
  
  What is the brand name and model number of the modem/ONT connected to the internet upstream of your RAX29?
  
  Those IP addresses are certainly suspicious, which makes the model of the modem/ONT a crucial detail.
  
  Just another user with time on their hands.
- bardiferously
  Aspirant
  Jan 21, 2025
  As just noted above, my cable modem (Xfinity) is a Netgear CM1100.
  - michaelkenward
    Guru - Experienced User
    Jan 21, 2025
    bardiferously wrote:
    
    As just noted above, my cable modem (Xfinity) is a Netgear CM1100.
    
    You mean as just added as the device? I see no earlier mention of CM1100.
    
    That is just a modem. No router component.
    
    You previously referred to the main wifi (SSID- FiOS-D3Q0Z) and the guest wifi (Rajah-5G-Guest). Are these SSIDs as you have set them up on the RAX29?
    
    If so, where does this bit come from:
    
    Manufacturer: Intel Corporation
    Description: Intel(R) Wi-Fi 6 AX201 160MHz
    
    Is that the wifi client? Netgear doesn't use Intel chips or drivers as far as I know.
    
    This may be why Kitsap asked about two different sources of Wi-Fi transmitting for your LAN.
    
    Then there is the 10.0.0.1 IP address. By default the router sits on 192.168.1.1. Unlike some manuals, the RAX29 doesn't even mention that one. You have to change that IP address deliberately.
    
    Did you make that change for a reason? It could offer a few more clues as to what is going on at your end. Nothing to do with squirrels I hope.
    
    Just another user with time on their hands.

Forum Discussion

RAX29 WiFi 6 Router not connecting at WiFi 6 with my laptop