Hi Again

I found the logs in the /var/log/frontview folder and the disk_smart.logs show all disks pass each time it runs. The other logs in here for the partitions, raid config and others "look" normal with nothing glaring out to me and all raids saying clean. There is also nothing in the smart_errors log files for each of the disks.

In the syslog in the main /var/log directory...i think i narrowed it down to around when the issue started and what i see in the logs is as follows:

At the weekly run of the smart check on Nov 22nd this message appears

Nov 22 06:47:06 READYNAS kernel: program smartctl.org is using a deprecated SCSI ioctl, please convert it to SG_IO
Nov 22 06:47:12 READYNAS last message repeated 15 times

Then it appears again a few seconds later
Nov 22 06:47:17 READYNAS kernel: program smartctl.org is using a deprecated SCSI ioctl, please convert it to SG_IO
Nov 22 06:47:22 READYNAS last message repeated 15 times

The disk_smart log from this day show nothing out of the ordinary with each disk passing with no errors.

Then something happens a few hours later that looks bad with a reboot and then a long period of time before it actually comes back up...

Nov 22 08:28:12 READYNAS kernel: EXT4-fs error (device dm-0): ext4_xattr_block_get: inode 112429004: bad block 1798836317
Nov 22 08:28:12 READYNAS kernel: EXT4-fs error (device dm-0): ext4_xattr_block_list: inode 112429004: bad block 1798836317
Nov 22 08:28:24 READYNAS kernel: EXT4-fs error (device dm-0): ext4_xattr_block_get: inode 112429004: bad block 1798836317
Nov 22 08:28:24 READYNAS kernel: EXT4-fs error (device dm-0): ext4_xattr_block_list: inode 112429004: bad block 1798836317
Nov 22 08:41:06 READYNAS shutdown[22621]: shutting down for system reboot
Nov 22 08:41:07 READYNAS init: Switching to runlevel: 6
Nov 22 08:41:23 READYNAS exiting on signal 15

Nov 22 09:26:27 READYNAS syslogd 1.5.0#6: restart.
Nov 22 09:26:27 READYNAS kernel: klogd 1.5.0#6, log source = /proc/kmsg started.
Nov 22 09:26:27 READYNAS kernel: Linux version 2.6.31.8.nv+v2 (root@NSBU-NJ) (gcc version 4.3.2 (sdk3.2rc1-ct-ng-1.4.1) ) #1 Thu Apr 18 17:40:54 HKT 2013
Nov 22 09:26:27 READYNAS kernel: ....Reboot messages continue.......

One part of the reboot messages that stands out to me is the messages about capacity change and unknow partition table but i don't know if this is normal or not.

Nov 22 09:26:27 READYNAS kernel: md2: detected capacity change from 0 to 8987273330688
Nov 22 09:26:27 READYNAS kernel: md2: unknown partition table

Then this message comes up throughout the logs a few more times throughout the next few days... Most recently this morning at 6:47 when it think it does its smart disk check cron job.
Nov 22 09:26:55 READYNAS kernel: program smartctl.org is using a deprecated SCSI ioctl, please convert it to SG_IO

Any ideas about this smartctl.org deprecated SCSI message? Is it perhaps the disk controller starting to go on the NAS? If it was simply one of the disks i would think it would show smart errors and not pass all the time.

Its also strange that i see transmission starting up in the logs but i see nothing at all about SabNZB...but again maybe this is normal. The syslog doesn't go back far enough for a "normal" successful boot for me to compare to.

I haven't done the boot menu disk check or the boot menu memory test yet...I guess those are next on the list if there isn't anything specific available on this smartctl message.

Thanks again.

Craig.

Forum Discussion

in my router wifi light light is not blinking