Reply

CM2050V 2.5 Gbps Multi-Gig Connection to RAX200

CAmbr52342
Tutor

CM2050V 2.5 Gbps Multi-Gig Connection to RAX200

Hello,

 

I am not sure which connection I need to make on the back of my RAX200 in order to use the 2.5Gbps from the modem.  Do I connect the modem to the multi-gig port on the back of the RAX200 or to the internet port?  I know I must also change the settings in the router's configuation page to 2.5 multi-gig.

 

Thanks! 

Message 1 of 7

Accepted Solutions
FURRYe38
Guru

Re: CM2050V 2.5 Gbps Multi-Gig Connection to RAX200

Please mark your thread as solved so others will know. 

Enjoy, Smiley Wink


@CAmbr52342 wrote:
Thank you! It works.

 

My Setup Internet Cable 1000↓/50↑ CAX80 Mode Mode | ISP SparkLight | Wifi Router Orbi RBK853 v4.6.7.5(Router Mode), Wired BackhaulSwitches Netgear GS105/8 | 

Additional NG HW: C7800/CM1100/CM1200/CM2000, Orbi CBK40, CBR750, RBK953(v6.0.3.68) & XR450(v130), RBK853 v4.6.7.5(AP) & RBK752 v4.6.7.5, RBK50(v23), SXK30(v110), R7000(v34), R7800(v84), R7960P(v84), EX7500/EX7700, GS308v3 and WNHDE111


 


 


Testing

View solution in original post

Message 7 of 7

All Replies
FURRYe38
Guru

Re: CM2050V 2.5 Gbps Multi-Gig Connection to RAX200

Please post about this here for your model router:
https://community.netgear.com/t5/Nighthawk-Routers-with-WiFi-6-AX/bd-p/en-home-routers-nighthawk-wif...

I would review the installation guide and user manual for the RAX200. I believe the 2.5Gb port can be used for the WAN side. You'll need to check for any configurations though.


Good Luck.

My Setup Internet Cable 1000↓/50↑ CAX80 Mode Mode | ISP SparkLight | Wifi Router Orbi RBK853 v4.6.7.5(Router Mode), Wired BackhaulSwitches Netgear GS105/8 | 

Additional NG HW: C7800/CM1100/CM1200/CM2000, Orbi CBK40, CBR750, RBK953(v6.0.3.68) & XR450(v130), RBK853 v4.6.7.5(AP) & RBK752 v4.6.7.5, RBK50(v23), SXK30(v110), R7000(v34), R7800(v84), R7960P(v84), EX7500/EX7700, GS308v3 and WNHDE111


 


 


Testing

Message 2 of 7
CAmbr52342
Tutor

Re: CM2050V 2.5 Gbps Multi-Gig Connection to RAX200

Thanks. I will try.

Message 3 of 7
plemans
Guru

Re: CM2050V 2.5 Gbps Multi-Gig Connection to RAX200

If the cm2050v is already activated, then connect it to the multigig port on the back of the rax200. you'll need to change the wan port in the settings to the multigig port and reboot both devices after its been changed. 

I've done it with my cm2000 on both my rax200 and my raxe500.  works great. 

Current Setup: CM2000-> RBK750-> GS716v2-> RAXE500-> Pi-hole->
Message 4 of 7
CAmbr52342
Tutor

Re: CM2050V 2.5 Gbps Multi-Gig Connection to RAX200

Thank you! It works.
Message 5 of 7
plemans
Guru

Re: CM2050V 2.5 Gbps Multi-Gig Connection to RAX200

glad to hear it!

Current Setup: CM2000-> RBK750-> GS716v2-> RAXE500-> Pi-hole->
Message 6 of 7
FURRYe38
Guru

Re: CM2050V 2.5 Gbps Multi-Gig Connection to RAX200

Please mark your thread as solved so others will know. 

Enjoy, Smiley Wink


@CAmbr52342 wrote:
Thank you! It works.

 

My Setup Internet Cable 1000↓/50↑ CAX80 Mode Mode | ISP SparkLight | Wifi Router Orbi RBK853 v4.6.7.5(Router Mode), Wired BackhaulSwitches Netgear GS105/8 | 

Additional NG HW: C7800/CM1100/CM1200/CM2000, Orbi CBK40, CBR750, RBK953(v6.0.3.68) & XR450(v130), RBK853 v4.6.7.5(AP) & RBK752 v4.6.7.5, RBK50(v23), SXK30(v110), R7000(v34), R7800(v84), R7960P(v84), EX7500/EX7700, GS308v3 and WNHDE111


 


 


Testing

View solution in original post

Message 7 of 7
Top Contributors
Discussion stats
  • 6 replies
  • 528 views
  • 2 kudos
  • 3 in conversation
Announcements

Orbi WiFi 6E