Antworten

Im Frontview wird kein Sicherheitsmodus angezeigt

ErrorBot
Aspirant

Im Frontview wird kein Sicherheitsmodus angezeigt

Hallo,

 

Ich hab ein 'kleines' Problem. Ich besitze zwei Baugleiche ReadyNAS NV+ (v1). Bei beiden wurde ein FW Update auf RAIDiator 4.1.14 durchgeführt. Während das bei dem einen Problemlos vonstatten ging, stellten sich bei dem anderen nach dem Neustart die Probleme ein:

 

okay.not.JPG

Wie auf dem Bild unschwer zu erkennen ist. wird im Frontview der Sicherheitsmodus nicht mehr angezeigt, sowie im unteren Teil des Bildes, die korrekte Anzahl von Festplatten im Healts-Status.

Das mit dem Health-Status kann ich noch verkraften. Über den Reiter Status-Status werden mir alle Festplatten angezeigt.

 

Bei dem Sicherheitsmodus sieht das jedoch anders aus. Ich betreibe eine AD und besitzte zur zeit nicht die Möglichkeit, das Gerät wieder in diese einzubinden.

 

Maßnahmen, die zu keinem Erfolg führten:

 

* Einspielen der Firmware über Frontview / USB-Stick

* Festplatten wipe / wechsel

* OS / Factory Reset

* Ziehen der Batterie

 

Irgendwer noch eine Idee?

 

Für irgendwelche gearteten Vorschläge bedanke ich mich schon im voraus.

 

Gruß

 

 

 

Nachricht 1 von 6

Akzeptierte Lösungen
ErrorBot
Aspirant

Re: Im Frontview wird kein Sicherheitsmodus angezeigt

Aus Verzweiflung habe ich auf dem 2ten Grät die Festplatten vorkonfiguriert und in das defekt Gerät eingesetzt. Das joinen in die AD hat geklappt und funktioniert für mich so weit ganz gut. Beim Anmelden über einen Browser ist Frontview bis auf den Frame Blank, aber so oft werde ich an dem Gerät auch keine Einstellungen mehr vornehmen. Gruß an alle die mir bei meinem Problem geholfen haben

Lösung in ursprünglichem Beitrag anzeigen

Nachricht 4 von 6

Alle Antworten
JennC
NETGEAR Employee Retired

Re: Im Frontview wird kein Sicherheitsmodus angezeigt

Hello ErrorBot,

 

Have you tried clearing the browser cache then try to access again the FrontView of the one that does not work? Please also try removing the other NAS from the network.

 

Welcome to the community!

 

Regards,

Nachricht 2 von 6
ErrorBot
Aspirant

Re: Im Frontview wird kein Sicherheitsmodus angezeigt

Hello JennC Thany for your reply. I have used differnt browser (Edge, Firefox, Vivaldi,etc) and also I clear the webcache. The result is all the time the same. frontview didn't show me the safe mode (Sicherheitsmodus). My ReadyNAS NV+ 's have static-IP's. The second NAS is only for backups online and use another ip subnet . Both NAS's didn't see each other. Any kind of other help? greatz
Nachricht 3 von 6
ErrorBot
Aspirant

Re: Im Frontview wird kein Sicherheitsmodus angezeigt

Aus Verzweiflung habe ich auf dem 2ten Grät die Festplatten vorkonfiguriert und in das defekt Gerät eingesetzt. Das joinen in die AD hat geklappt und funktioniert für mich so weit ganz gut. Beim Anmelden über einen Browser ist Frontview bis auf den Frame Blank, aber so oft werde ich an dem Gerät auch keine Einstellungen mehr vornehmen. Gruß an alle die mir bei meinem Problem geholfen haben
Nachricht 4 von 6
JennC
NETGEAR Employee Retired

Re: Im Frontview wird kein Sicherheitsmodus angezeigt

Hello ErrorBot,

 

This model is too old, I can't find our old NV+ here to see if I get the same results. Can you make sure you have full backup of the data too? Then upgrade to 4.1.15 version.

 

Regards,

Nachricht 5 von 6
JennC
NETGEAR Employee Retired

Re: Im Frontview wird kein Sicherheitsmodus angezeigt

Hello ErrorBot,

 

We’d greatly appreciate hearing your feedback letting us know if the information we provided has helped resolve your issue or if you need further assistance. 
If your issue is now resolved, we encourage you to mark the appropriate reply as the “Accept as Solution” so others can be confident in benefiting from the solution. 
 
The Netgear community looks forward to hearing from you and being a helpful resource in the future!
 
Regards,

Nachricht 6 von 6
Diskussionsstatistiken
  • 5 Antworten
  • 2888 Aufrufe
  • 0 Kudos
  • 2 in Unterhaltung