Orbi WiFi 7 RBE973
Reply

FVS318N Login Issue

PETROV
Tutor

FVS318N Login Issue

I have bricked my firwall after a factory reset,

After a reboot it seems to boot normaly but nothing works (only as a hup)

Now i can nolonger access the device,

I am not able to telnet or web access the divice at all,  and also i feel that it dit not reset the password.

De default IP 192.168.1.1 (192.168.0.1) does nog give any response so i can not ping

 

I am able to connect to the console with a serial connection, and boot the device here i see lots of errors seems the whole SQL is corrupt. after booting i get the message FVS318  Login:

 

I am not able to login here nothing seems to work here

 

When booting and pressing a key the auto boot stops an i can sent commands to the device

 

How can ido a firmware update from this point,

 

Will attach part of the messages

U-Boot 2008.10-mpcore-svn70 (Dec 16 2013 - 13:31:40)

Cavium Networks CNS3XXX SDK v0.7-1202

 

CPU: Cavium Networks CNS3000

ID Code: 410fb024 (Part number: 0xB02, Revision number: 4)

CPU ID: 900

Chip Version: c

 

DRAM:  128 MB

Flash: 32 MB

*** Warning - bad CRC, using default environment

 

In:    serial

Out:   serial

Err:   serial

CPU works at 300 MHz (600/1/2)

DDR2 Speed is 266 MHz

switch/phy reset

## Starting application at 0x03000000 ...

Hello ,This is SC world!

BootVersion SC V105,Build Time:Dec 16 2013 - 13:31:26

## Application terminated, rc = 0x0

 

checking the integrality of linux ... ...

flen   is    :1a84f00

fcrc   is    :2632bc82

vmoffset   is    :100

vmsize   is    :818ffe

vmcrc   is    :5b0b7266

crc caled  is    :5b0b7266

kernel length  is    :8491006(0x818ffe)

fw version is    :4.3.3-5

checking pass..

Hit any key to stop autoboot:  0

enter do_eth_down!!!

## Starting application at 0x02000000 ...

Uncompressing Li.................................................................................................................... done, booting

Linux version 2.6.31.1-cavm1 (root@localhost.localdomain) (gcc version 4.3.3 (Buildroot 2010.05) ) #1 Wed Jun 3 13:06:54 IST 2015

Cavium Networks CNS3XXX SDK v1.1-1952

CPU: ARMv6-compatible processor [410fb024] revision 4 (ARMv7), cr=00c5387f

CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache

Machine: Cavium Networks ARM11 MPCore

Memory policy: ECC disabled, Data cache writeback

Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512

Kernel command line: root=/dev/ram0 rw init=/linuxrc mem=128M console=ttyS0,9600

PID hash table entries: 512 (order: 9, 2048 bytes)

Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)

Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)

Memory: 128MB = 128MB total

Memory: 119508KB available (3324K code, 252K data, 116K init, 0K highmem)

NR_IRQS:96

console [ttyS0] enabled

Calibrating delay loop... 119.60 BogoMIPS (lpj=598016)

Mount-cache hash table entries: 512

CPU: Testing write buffer coherency: ok

NET: Registered protocol family 16

Initializing CNS3XXX L2 cache controller... done.

Initializing CNS3XXX DMA controller

First time microcode alloc for channel 0 done @phy:26057000

First time microcode alloc for channel 1 done @phy:26058000

First time microcode alloc for channel 2 done @phy:26059000

First time microcode alloc for channel 3 done @phy:2605a000

First time microcode alloc for channel 4 done @phy:2605b000

First time microcode alloc for channel 5 done @phy:26030000

First time microcode alloc for channel 6 done @phy:26031000

First time microcode alloc for channel 7 done @phy:2602e000

First time microcode alloc for channel 8 done @phy:2602f000

Cavium EVB Board version 1.x

bio: create slab <bio-0> at 0

SCSI subsystem initialized

Slow work thread pool: Starting up

Slow work thread pool: Ready

FS-Cache: Loaded

NET: Registered protocol family 2

IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

TCP established hash table entries: 4096 (order: 3, 32768 bytes)

TCP bind hash table entries: 4096 (order: 2, 16384 bytes)

TCP: Hash tables configured (established 4096 bind 4096)

TCP reno registered

NET: Registered protocol family 1

Trying to unpack rootfs image as initramfs...

rootfs image is not initramfs (no cpio magic); looks like an initrd

Freeing initrd memory: 6448K

CNS3XXX PCIe Host Control Driver

 

pci_common_init(&cns3xxx_pcie0); is marked off to disable pci-e0

 

PCI-E1 uses internal clock source.

Enable PCIe PMU CLK

patch to disable pcie0

Enable PCIe1 Internal CLK

PCIE-1 equalizer setting, val:0xe2c

Active PCIe1 Clock, PHY and reset PCIe

PCIe: Port[1] Enable PCIe LTSSM

PCIe: Port[1] Check data link layer...Link up.

PCIe: Set Device Max_Read_Request_Size to 128 byte

pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot D3cold

pci 0001:00:00.0: PME# disabled

pci 0001:00:01.0: PME# supported from D0 D1 D3hot

pci 0001:00:01.0: PME# disabled

PCI: bus0: Fast back to back transfers disabled

PCI: bus1: Fast back to back transfers enabled

PCIe1: Bridge found.

PCI: enabling device 0001:00:00.0 (0140 -> 0143)

PCIe1 map irq: 0001:00:00.00 slot 0, pin 1, irq: 88

PCIe1 map irq: 0001:00:01.00 slot 1, pin 1, irq: 62

squashfs: version 4.0 (2009/01/31) Phillip Lougher

JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.

msgmni has been set to 246

alg: No test for cipher_null (cipher_null-generic)

alg: No test for ecb(cipher_null) (ecb-cipher_null)

alg: No test for digest_null (digest_null-generic)

alg: No test for compress_null (compress_null-generic)

alg: No test for stdrng (krng)

io scheduler noop registered

io scheduler cfq registered (default)

cns3xxx_spi_probe: setup CNS3XXX SPI Controller in polling mode, w/o DMA

Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled

serial8250: ttyS0 at MMIO 0x78000000 (irq = 45) is a 16550A

brd: module loaded

loop: module loaded

cns3xxxflash: Found 1 x16 devices at 0x0 in 16-bit bank

 Amd/Fujitsu Extended Query Table at 0x0040

cns3xxxflash: CFI does not contain boot bank location. Assuming top.

number of CFI chips: 1

cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.

CNS3XXX NOR flash: Using static partition definition

Creating 8 MTD partitions on "cns3xxxflash":

0x000000000000-0x000000040000 : "UBoot"

0x000000040000-0x000000060000 : "Manuinfo "

0x000000060000-0x000000080000 : "Calibration "

0x000000080000-0x000000980000 : "Kernel"

0x000000980000-0x000001de0000 : "File System"

0x000001de0000-0x000001fe0000 : "Configure"

0x000001fe0000-0x000002000000 : "UBootEnv"

0x000000000000-0x000002000000 : "ALL"

Initialize PHY s/w auto-polling

CNS3XXX PSE: Initialize

MAC 0

Initialize BCM53115M

enable UNKNOW_TAP_TOCPU

bcm53115M device id:(0x53128)

MAC 1

Initialize brcm50612

MAC 2

jumbo_frame off

MAX_PACKET_LEN:1536

PPP generic driver version 2.4.2

PPP BSD Compression module registered

PPP MPPE Compression module registered

NET: Registered protocol family 24

CNS3XXX Real Time Clock, (c) 2009 Cavium Networks

rtc irq:23

cns3xxx-rtc cns3xxx-rtc: rtc core: registered cns3xxx-rtc as rtc0

i2c /dev entries driver

i2c-gpio i2c-gpio.1: using pins 1 (SDA) and 0 (SCL)

cns3xxx_i2c_init:

cns3xxx_i2c_probe:

GACT probability NOT on

Mirror/redirect action on

u32 classifier

    Performance counters on

    Actions configured

Netfilter messages via NETLINK v0.30.

nf_conntrack version 0.5.0 (2048 buckets, 8192 max)

CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use

nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or

sysctl net.netfilter.nf_conntrack_acct=1 to enable it.

ctnetlink v0.93: registering with nfnetlink.

xt_time: kernel timezone is -0000

ip_tables: (C) 2000-2006 Netfilter Core Team

ipt_account 0.1.7 : Piotr Gasid▒o <quaker@barbara.eu.org>, http://www.barbara.eu.org/~quaker/ipt_account/

TCP cubic registered

NET: Registered protocol family 10

ip6_tables: (C) 2000-2006 Netfilter Core Team

IPv6 over IPv4 tunneling driver

NET: Registered protocol family 17

RPC: Registered udp transport module.

RPC: Registered tcp transport module.

802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>

All bugs added by David S. Miller <davem@redhat.com>

VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 4

cns3xxx-rtc cns3xxx-rtc: setting system clock to 1970-01-01 00:00:00 UTC (0)

RAMDISK: gzip image found at block 0

VFS: Mounted root (ext2 filesystem) on device 1:0.

Freeing init memory: 116K

/etc/init.d/rcS starting

Booting FVS318N User Space...

 

Mounting file systems

SQUASHFS error: zlib_inflate error, data probably corrupt

SQUASHFS error: squashfs_read_data failed to read block 0xf30447

SQUASHFS error: Unable to read fragment cache entry [f30447]

SQUASHFS error: Unable to read page, block f30447, size c279

SQUASHFS error: Unable to read fragment cache entry [f30447]

SQUASHFS error: Unable to read page, block f30447, size c279

SQUASHFS error: Unable to read fragment cache entry [f30447]

SQUASHFS error: Unable to read page, block f30447, size c279

SQUASHFS error: Unable to read fragment cache entry [f30447]

SQUASHFS error: Unable to read page, block f30447, size c279

SQUASHFS error: Unable to read fragment cache entry [f30447]

SQUASHFS error: Unable to read page, block f30447, size c279

SQUASHFS error: Unable to read fragment cache entry [f30447]

SQUASHFS error: Unable to read page, block f30447, size c279

SQUASHFS error: Unable to read fragment cache entry [f30447]

SQUASHFS error: Unable to read page, block f30447, size c279

SQUASHFS error: Unable to read fragment cache entry [f30447]

SQUASHFS error: Unable to read page, block f30447, size c279

SQUASHFS error: Unable to read fragment cache entry [f30447]

SQUASHFS error: Unable to read page, block f30447, size c279

SQUASHFS error: Unable to read fragment cache entry [f30447]

SQUASHFS error: Unable to read page, block f30447, size c279

SQUASHFS error: Unable to read fragment cache entry [f30447]

SQUASHFS error: Unable to read page, block f30447, size c279

SQUASHFS error: Unable to read fragment cache entry [f30447]

SQUASHFS error: Unable to read page, block f30447, size c279

SQUASHFS error: Unable to read fragment cache entry [f30447]

SQUASHFS error: Unable to read page, block f30447, size c279

SQUASHFS error: Unable to read fragment cache entry [f30447]

SQUASHFS error: Unable to read page, block f30447, size c279

 

 

Model: FVS318G|ProSafe Gigabit 8 Port VPN Firewall
Message 1 of 7
DaneA
NETGEAR Employee Retired

Re: FVS318N Login Issue

Hi PETROV,

 

Welcome to the community! 🙂 

 

Let us try to power reset the FVS318N.  Kindly do the steps below:

 

1. Disconnect the FVS318N from your existing network and make sure its turned on.  Get a straightened paper clip.

2. Insert the paper clip to the factory defaults hole then press and hold the factory reset button inside it for 30 seconds.

3. After 30 seconds, turn OFF the FVS318N while you still continue to press and hold the factory reset button.  Wait for 5 seconds.

4. After 5 seconds, turn ON the FVS318N while you still continue to press and hold the factory reset button.  Wait for another 5 seconds.

5. After 5 seconds, release the paper clip from the factory reset button.  Wait for the FVS318N to boot up properly.  Observe the LED lights as well.

6. After it boots up, connect a PC/laptop to any LAN port of the FVS318N then try to login to its web-GUI.

 

Kindly answer the questions below:

 

a. What is the behavior of the LED lights after doing the power reset?

b. Are you able to get a valid IP address when you connect a PC/laptop to any port of the FVS318N?

c. Are you able to access and login to the web-GUI of the FSV318N/

 

 

Regards,

 

DaneA
NETGEAR Community Team

Message 2 of 7
PETROV
Tutor

Re: FVS318N Login Issue

After i have done al the above
 the device boots, green LED is on
Alle the lan leds light en go off again
the orange (test) LED goes on for some time
Orange turns off and the second green LED goes on Wireless
After this i can connect a lan cable the indicators shows green and orange,
I do not get a valid ip address on my PC.
I can not access the web-GUI, i can not ping any IP addres 192.168.1.1 or 192.168.0.1

When connecting to the console i get a lot of errors see message below

what can I do to solve this

Thank you for looking in to this

U-Boot 2008.10-mpcore-svn70 (Dec 16 2013 - 13:31:40)

Cavium Networks CNS3XXX SDK v0.7-1202

 

CPU: Cavium Networks CNS3000

ID Code: 410fb024 (Part number: 0xB02, Revision number: 4)

CPU ID: 900

Chip Version: c

 

DRAM: 128 MB

Flash: 32 MB

*** Warning - bad CRC, using default environment

 

In:   serial

Out:   serial

Err:   serial

CPU works at 300 MHz (600/1/2)

DDR2 Speed is 266 MHz

switch/phy reset

## Starting application at 0x03000000 ...

Hello ,This is SC world!

BootVersion SC V105,Build Time:Dec 16 2013 - 13:31:26

## Application terminated, rc = 0x0

 

checking the integrality of linux ... ...

flen   is           :1a84f00

fcrc   is           :2632bc82

vmoffset   is           :100

vmsize   is           :818ffe

vmcrc   is           :5b0b7266

crc caled is           :5b0b7266

kernel length is           :8491006(0x818ffe)

fw version is   :4.3.3-5

checking pass..

Hit any key to stop autoboot: 0

enter do_eth_down!!!

## Starting application at 0x02000000 ...

Uncompressing Li.................................................................................................................... done, booting

Linux version 2.6.31.1-cavm1 (root@localhost.localdomain) (gcc version 4.3.3 (Buildroot 2010.05) ) #1 Wed Jun 3 13:06:54 IST 2015

Cavium Networks CNS3XXX SDK v1.1-1952

CPU: ARMv6-compatible processor [410fb024] revision 4 (ARMv7), cr=00c5387f

CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache

Machine: Cavium Networks ARM11 MPCore

Memory policy: ECC disabled, Data cache writeback

Built 1 zonelists in Zone order, mobility grouping on.         Total pages: 32512

Kernel command line: root=/dev/ram0 rw init=/linuxrc mem=128M console=ttyS0,9600

PID hash table entries: 512 (order: 9, 2048 bytes)

Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)

Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)

Memory: 128MB = 128MB total

Memory: 119508KB available (3324K code, 252K data, 116K init, 0K highmem)

NR_IRQS:96

console [ttyS0] enabled

Calibrating delay loop... 119.60 BogoMIPS (lpj=598016)

Mount-cache hash table entries: 512

CPU: Testing write buffer coherency: ok

NET: Registered protocol family 16

Initializing CNS3XXX L2 cache controller... done.

Initializing CNS3XXX DMA controller

First time microcode alloc for channel 0 done @phy:26057000

First time microcode alloc for channel 1 done @phy:26058000

First time microcode alloc for channel 2 done @phy:26059000

First time microcode alloc for channel 3 done @phy:2605a000

First time microcode alloc for channel 4 done @phy:2605b000

First time microcode alloc for channel 5 done @phy:26030000

First time microcode alloc for channel 6 done @phy:26031000

First time microcode alloc for channel 7 done @phy:2602e000

First time microcode alloc for channel 8 done @phy:2602f000

Cavium EVB Board version 1.x

bio: create slab <bio-0> at 0

SCSI subsystem initialized

Slow work thread pool: Starting up

Slow work thread pool: Ready

FS-Cache: Loaded

NET: Registered protocol family 2

IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

TCP established hash table entries: 4096 (order: 3, 32768 bytes)

TCP bind hash table entries: 4096 (order: 2, 16384 bytes)

TCP: Hash tables configured (established 4096 bind 4096)

TCP reno registered

NET: Registered protocol family 1

Trying to unpack rootfs image as initramfs...

rootfs image is not initramfs (no cpio magic); looks like an initrd

Freeing initrd memory: 6448K

CNS3XXX PCIe Host Control Driver

 

pci_common_init(&cns3xxx_pcie0); is marked off to disable pci-e0

 

PCI-E1 uses internal clock source.

Enable PCIe PMU CLK

patch to disable pcie0

Enable PCIe1 Internal CLK

PCIE-1 equalizer setting, val:0xe2c

Active PCIe1 Clock, PHY and reset PCIe

PCIe: Port[1] Enable PCIe LTSSM

PCIe: Port[1] Check data link layer...Link up.

PCIe: Set Device Max_Read_Request_Size to 128 byte

pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot D3cold

pci 0001:00:00.0: PME# disabled

pci 0001:00:01.0: PME# supported from D0 D1 D3hot

pci 0001:00:01.0: PME# disabled

PCI: bus0: Fast back to back transfers disabled

PCI: bus1: Fast back to back transfers enabled

PCIe1: Bridge found.

PCI: enabling device 0001:00:00.0 (0140 -> 0143)

PCIe1 map irq: 0001:00:00.00 slot 0, pin 1, irq: 88

PCIe1 map irq: 0001:00:01.00 slot 1, pin 1, irq: 62

squashfs: version 4.0 (2009/01/31) Phillip Lougher

JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.

msgmni has been set to 246

alg: No test for cipher_null (cipher_null-generic)

alg: No test for ecb(cipher_null) (ecb-cipher_null)

alg: No test for digest_null (digest_null-generic)

alg: No test for compress_null (compress_null-generic)

alg: No test for stdrng (krng)

io scheduler noop registered

io scheduler cfq registered (default)

cns3xxx_spi_probe: setup CNS3XXX SPI Controller in polling mode, w/o DMA

Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled

serial8250: ttyS0 at MMIO 0x78000000 (irq = 45) is a 16550A

brd: module loaded

loop: module loaded

cns3xxxflash: Found 1 x16 devices at 0x0 in 16-bit bank

Amd/Fujitsu Extended Query Table at 0x0040

cns3xxxflash: CFI does not contain boot bank location. Assuming top.

number of CFI chips: 1

cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.

CNS3XXX NOR flash: Using static partition definition

Creating 8 MTD partitions on "cns3xxxflash":

0x000000000000-0x000000040000 : "UBoot"

0x000000040000-0x000000060000 : "Manuinfo "

0x000000060000-0x000000080000 : "Calibration "

0x000000080000-0x000000980000 : "Kernel"

0x000000980000-0x000001de0000 : "File System"

0x000001de0000-0x000001fe0000 : "Configure"

0x000001fe0000-0x000002000000 : "UBootEnv"

0x000000000000-0x000002000000 : "ALL"

Initialize PHY s/w auto-polling

CNS3XXX PSE: Initialize

MAC 0

Initialize BCM53115M

enable UNKNOW_TAP_TOCPU

bcm53115M device id:(0x53128)

MAC 1

Initialize brcm50612

MAC 2

jumbo_frame off

MAX_PACKET_LEN:1536

PPP generic driver version 2.4.2

PPP BSD Compression module registered

PPP MPPE Compression module registered

NET: Registered protocol family 24

CNS3XXX Real Time Clock, (c) 2009 Cavium Networks

rtc irq:23

cns3xxx-rtc cns3xxx-rtc: rtc core: registered cns3xxx-rtc as rtc0

i2c /dev entries driver

i2c-gpio i2c-gpio.1: using pins 1 (SDA) and 0 (SCL)

cns3xxx_i2c_init:

cns3xxx_i2c_probe:

GACT probability NOT on

Mirror/redirect action on

u32 classifier

   Performance counters on

   Actions configured

Netfilter messages via NETLINK v0.30.

nf_conntrack version 0.5.0 (2048 buckets, 8192 max)

CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use

nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or

sysctl net.netfilter.nf_conntrack_acct=1 to enable it.

ctnetlink v0.93: registering with nfnetlink.

xt_time: kernel timezone is -0000

ip_tables: (C) 2000-2006 Netfilter Core Team

ipt_account 0.1.7 : Piotr Gasid▒o <quaker@barbara.eu.org>, http://www.barbara.eu.org/~quaker/ipt_account/

TCP cubic registered

NET: Registered protocol family 10

ip6_tables: (C) 2000-2006 Netfilter Core Team

IPv6 over IPv4 tunneling driver

NET: Registered protocol family 17

RPC: Registered udp transport module.

RPC: Registered tcp transport module.

802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>

All bugs added by David S. Miller <davem@redhat.com>

VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 4

cns3xxx-rtc cns3xxx-rtc: setting system clock to 1970-01-01 00:00:00 UTC (0)

RAMDISK: gzip image found at block 0

VFS: Mounted root (ext2 filesystem) on device 1:0.

Freeing init memory: 116K

/etc/init.d/rcS starting

Booting FVS318N User Space...

 

Mounting file systems

SQUASHFS error: zlib_inflate error, data probably corrupt

SQUASHFS error: squashfs_read_data failed to read block 0xf30447

SQUASHFS error: Unable to read fragment cache entry [f30447]

SQUASHFS error: Unable to read page, block f30447, size c279

SQUASHFS error: Unable to read fragment cache entry [f30447]

SQUASHFS error: Unable to read page, block f30447, size c279

SQUASHFS error: Unable to read fragment cache entry [f30447]

SQUASHFS error: Unable to read page, block f30447, size c279

SQUASHFS error: Unable to read fragment cache entry [f30447]

SQUASHFS error: Unable to read page, block f30447, size c279

SQUASHFS error: Unable to read fragment cache entry [f30447]

SQUASHFS error: Unable to read page, block f30447, size c279

SQUASHFS error: Unable to read fragment cache entry [f30447]

SQUASHFS error: Unable to read page, block f30447, size c279

SQUASHFS error: Unable to read fragment cache entry [f30447]

SQUASHFS error: Unable to read page, block f30447, size c279

SQUASHFS error: Unable to read fragment cache entry [f30447]

SQUASHFS error: Unable to read page, block f30447, size c279

SQUASHFS error: Unable to read fragment cache entry [f30447]

SQUASHFS error: Unable to read page, block f30447, size c279

SQUASHFS error: Unable to read fragment cache entry [f30447]

SQUASHFS error: Unable to read page, block f30447, size c279

SQUASHFS error: Unable to read fragment cache entry [f30447]

SQUASHFS error: Unable to read page, block f30447, size c279

SQUASHFS error: Unable to read fragment cache entry [f30447]

SQUASHFS error: Unable to read page, block f30447, size c279

SQUASHFS error: Unable to read fragment cache entry [f30447]

SQUASHFS error: Unable to read page, block f30447, size c279

SQUASHFS error: Unable to read fragment cache entry [f30447]

SQUASHFS error: Unable to read page, block f30447, size c279

SQUASHFS error: Unable to read fragment cache entry [f30447]

SQUASHFS error: Unable to read page, block f30447, size c279

SQUASHFS error: Unable to read fragment cache entry [f30447]

SQUASHFS error: Unable to read page, block f30447, size c279

SQUASHFS error: Unable to read fragment cache entry [f30447]

SQUASHFS error: Unable to read page, block f30447, size c279

SQUASHFS error: Unable to read fragment cache entry [f30447]

SQUASHFS error: Unable to read page, block f30447, size c279

SQUASHFS error: Unable to read fragment cache entry [f30447]

SQUASHFS error: Unable to read page, block f30447, size c279

SQUASHFS error: Unable to read fragment cache entry [f30447]

SQUASHFS error: Unable to read page, block f30447, size c279

SQUASHFS error: Unable to read fragment cache entry [f30447]

SQUASHFS error: Unable to read page, block f30447, size c279

SQUASHFS error: Unable to read fragment cache entry [f30447]

SQUASHFS error: Unable to read page, block f30447, size c279

SQUASHFS error: Unable to read fragment cache entry [f30447]

SQUASHFS error: Unable to read page, block f30447, size c279

insmod: read error from '/pfrm2.0/lib/modules/spp[kernel mode] CNS3XXX_ARL_TABLE_ADD

e.ko': Input/output error

insmod: can't insert '/pfrm2.0/lib/modules/sppe.ko': Input/output error

Enabling Quiet Boot...Done

Setting up loopback

net.ipv6.conf.eth1.accept_ra = 0

Setting Hostname... Done.

Sat Jan 1 00:00:00 UTC 2011

Jan 1 00:00:00 FVS318N syslog.info syslogd started: BusyBox v1.17.4

starting tr69 daemon configuration....done

umiInit failed

loggingInit failed

SQL error near line 3: no such table: sqliteLock

starting firewalld Daemon...Done

inserting default firewall rules

Restoring certficates from persistant storage...Done

Starting pnac daemon...Done

iwpriv wifi0 setCountryID 528Starting dot11 daemon...Done

Loading WpsPB Module..umiInit failed

rebootd : umi initialization failed

starting SNMP Daemon...Done

Starting the cron deamon...Done

starting ntpd Daemon...Done

Starting NIMF daemon... Done

Starting LINKDETECT daemon... Done

Creating /dev/pts/0 pseudo device for L2TP <-> PPP communication... Done

Starting IKE Daemon...

Failed to Open /dev/bcmDebug device

Done

Done

Starting VPN KEEP ALIVE Daemon...Done

Bandwidth Profile Initialization...Done

SSLVPN Intialization ....... Done

Webserver Starting....Done

net.ipv6.conf.eth1.accept_ra = 0

Creating Dummy Config File

Restoring configuration from persistant storage...

SQL error near line 3: no such table: defaultMac

SQL error near line 4: no such table: defaultMac

SQL error near line 5: no such table: defaultMac

SQL error near line 6: no such table: unitInfo

SQL error near line 7: no such table: ipAddressTable

Making Brand.conf...

Loading Factory Defaults Modulescan't open device gpio-device

Inserting the bcm debug module...Done

Inserting the power saving module...Done

making database from system settings...

ifDevUpdtMac SQL error: no such table: ethernet

ifDevUpdtMac SQL error: no such table: ethernet

SQL error near line 4: no such table: ConfigPort

Copying necessary files for L2TP Server...

Done

Executing bcmRegConfig...

 

bcmRegConfig :Failed to Open /dev/bcmDebug device

 

bcmRegConfig :Failed to Open /dev/bcmDebug device

 

bcmRegConfig :Failed to Open /dev/bcmDebug device

 

bcmRegConfig :Failed to Open /dev/bcmDebug device

 

bcmRegConfig :Failed to Open /dev/bcmDebug device

 

bcmRegConfig :Failed to Open /dev/bcmDebug device

 

bcmRegConfig :Failed to Open /dev/bcmDebug device

 

bcmRegConfig :Failed to Open /dev/bcmDebug device

 

bcmRegConfig :Failed to Open /dev/bcmDebug device

Done

Dumping SYSTEM_MENU_INFO

hwver: 00:00:A0:03

reginfo: 0x0003

numofimages : 1

 

currimage: 1

mac address : 6CB0CE763DC8

 

wireless MAC[0] : 6cb0ce763dda

wireless MAC[1] : 6cb0ce763ddb

wireless MAC[2] : 6cb0ce763ddc

wireless MAC[3] : 6cb0ce763ddd

vlan[0] MAC : 6cb0ce763dcb

vlan[1] MAC : 6cb0ce763dcc

vlan[2] MAC : 6cb0ce763dcd

vlan[3] MAC : 6cb0ce763dce

vlan[4] MAC : 6cb0ce763dcf

vlan[5] MAC : 6cb0ce763dd0

vlan[6] MAC : 6cb0ce763dd1

vlan[7] MAC : 6cb0ce763dd2

vlan[8] MAC : 6cb0ce763dd3

vlan[9] MAC : 6cb0ce763dd4

vlan[10] MAC : 6cb0ce763dd5

vlan[11] MAC : 6cb0ce763dd6

vlan[12] MAC : 6cb0ce763dd7

vlan[13] MAC : 6cb0ce763dd8

vlan[14] MAC : 6cb0ce763dd9

WAN MAC : 6cb0ce763dc9

 

pcbasn number : R.YX249204D6

 

serial number : 3BT349BD00404

 

image 0 : 4.3.3-5

image 1 : 0

productId : FVS318N

 

maccnt0: 0x22

maccnt1: 0x0

maccnt2: 0x0

maccnt3: 0x0

Done

Wed Jun 3 10:13:30 UTC 2015

################################################

 

 

Secure Gateway Solution for FVS318N

 

FVS318N login:

Message 3 of 7
DaneA
NETGEAR Employee Retired

Re: FVS318N Login Issue

Hi PETROV,

 

Based on the results you have posted, it seems that the FVS318N got faulty.  With regard to this, I suggest you to open an online case with NETGEAR Support at anytime.  State what happened to your FVS318N and the troubleshooting steps we tried.  Attach a .pdf or .doc copy of the Proof of Purchase or Sales Invoice of your FVS318N for warranty verification.  If ever the hardware warranty is still valid, an online replacement will follow.

 

 

Regards,

 

DaneA

NETGEAR Community Team

Message 4 of 7
PETROV
Tutor

Re: FVS318N Login Issue

I am not able to open an online case or upload documents

I can call or open a chat

 

I do have the proof of purchase, but did not register the firewall as the equipment has been used on different places by different people

 

 

Message 5 of 7
DaneA
NETGEAR Employee Retired

Re: FVS318N Login Issue

Hi PETROV,

 

If ever you were able to open an online case with NETGEAR Support, kindly keep us posted about the progress of it.

 

 

Regards,

 

DaneA

NETGEAR Community Team

Message 6 of 7
DaneA
NETGEAR Employee Retired

Re: FVS318N Login Issue

@PETROV,

 

I just want to follow-up on this. Were you able to open an online case with NETGEAR Support?  If yes, kindly keep us posted about the progress of it.

 

 

Regards,

 

DaneA

NETGEAR Community Team

Message 7 of 7
Discussion stats
  • 6 replies
  • 5128 views
  • 0 kudos
  • 2 in conversation
Announcements