Showing ideas with label Smart Managed Plus Switch.
Show all ideas
Submitted on
2016-06-08
11:19 AM
Submitted by
dannygti
on
2016-06-08
11:19 AM
Can we get the software to be supported on MAC computers?
... View more
See more ideas labeled with:
-
Smart Managed Plus Switch
Given that your entire product line of ProSafe Smart switches only supports up to TLS 1.0, I'd like to suggest that you start working on making TLS 1.3 available. Especially, since TLS 1.2 has been around since 2008 and you should really be embarassed that your business line of switches only support insecure communication methods.
... View more
See more ideas labeled with:
-
Smart Managed Plus Switch
-
Smart Switch
Submitted on
2016-01-07
02:16 PM
Submitted by
Phoenixxl
on
2016-01-07
02:16 PM
Hello to anyone taking the time to read this.
I have close to a dozen netgear GS1xxE switches at my home and various family member's homes by now and swear by the things. Vlan tagging is a must for our various setups and these switches haven't disapointed yet.
However , when it comes to configuring them, the fact one is incapable of selecting the vlan on which the things do their DHCP negotiating forces me to use fixed IP's.
In essence this isn't all that bad. But adding this to the firmware isn't something unreasonable to ask I would think.
http://i.imgur.com/JZEvBx4.png
http://i.imgur.com/p9evrYY.png
Thanks in advance for taking the time to reply. If you also think this slight oversight should be rectified please do reply.
... View more
See more ideas labeled with:
-
Smart Managed Plus Switch
Please add the funtion to select VLan for management.
Thanx
... View more
See more ideas labeled with:
-
Smart Managed Plus Switch
Any chance that LAG will be available on the GS308E in future firmware updates?
... View more
See more ideas labeled with:
-
Smart Managed Plus Switch
-
Smart Switch
Hi,
is great to have the possibility to configure the VLAN management interface.
Thx!
Claudio
... View more
See more ideas labeled with:
-
Smart Managed Plus Switch
Please consider using HTTPS for the web management of the GS1xxE line of switches.
Especially the smaller models need a secure way to configure them as there are no real replacements for in-field deployments outside special technical rooms where is no room to fit an entire rack into...
As the current state of security of many of the embedded or IoT thingis is sub-optimal it is crucial to prevent login credential sniffing via other pOwnd network devices within the same subnet.
Thanks,
Stefan Seide
... View more
See more ideas labeled with:
-
Smart Managed Plus Switch
Status:
New Idea
Submitted on
2018-08-03
04:59 AM
Submitted by
sasha-london
on
2018-08-03
04:59 AM
Hi
I'm aware of the previous discusions/sugestions here about adding the ability to specify a managemet vlan on ProSAFE Plus lineup (e.g.GS108Ev3). While there are good alternatives higher up the line that do support this (GS108Ev3->GS108Tv2) I dont see a similar aternative for GS105PE - a-5 port passthrough POE switch. It would really be appreciated if this feature could be added to GS105PE. I think it would make the switch so much better. It does almost everything needed for this type of device - just lacking the management vlan.
Thanks,
Sasha
... View more
See more ideas labeled with:
-
Smart Managed Plus Switch
I've just added a GS108Ev3 to my network, to add to an existing GS116Ev2. I am very disappointed to see that the 108 does not support a port description field which is present in the 116. Can this not be added?
... View more
See more ideas labeled with:
-
Smart Managed Plus Switch
Please look to add Port Description naming to the gs305e managed switch. With lots of devices and switches using port numbers is cumbersome.. names would be more efficient to manage.
... View more
See more ideas labeled with:
-
Smart Managed Plus Switch
The GS105E v2 (5 port) and GS116E v2 (16 port) switches have the ability to disable Energy Efficient Ethernet (IEEE 802.3az) in the web interface via: System > Management > Power Saving Mode, Enable/Disable This option is missing from the GS108E v3 (8 port) switch. Can this be addressed in a future firmware update?
... View more
See more ideas labeled with:
-
Smart Managed Plus Switch
Hello:
The GS105PE switch is a great idea and potential problem solver. Unfortunately, due to one design flaw, it is only "almost" useful.
There are a few different switches that support PoE Passthrough on a single port. What makes this switch so awesome is that it has two ports. With an 802.3at (PoE+) feed, there is enough power to power two devices of common PoE types (for example, two PoE telephones). Of course, with this its also potentially possible to plug in two devices that use too much power and end up overloading the feed port. Fortunately, MOST poe devices out there do not have this problem.
Unfortunately, this switch is hamstrung by a design choice: the overload problem is solved by PoE class limitations rather than actual current limits. In order to use both ports, you have to plug in class 1/2 devices, if you have even one class0 or class3 device, then you only get one. Period. Even if that device only wants 2.5w.
This is a more extreme problem than it appears because most PoE PE chip makers have switched to only making class 3 chips. Thus most devices advertise class 3, even if they only need class 2. Except for this switch, this is no issue, as normal PoE switches regulate by combined power, not class. That's why I can get an 8 port 60W PoE switch that supports class 3. At full class 3, that allows nearly 13 watts per port, or 104W for all 8 ports.
It appears Netgear used this worst-case design method when designing this device. Please correct this huge oversight and just use power limiting rather than class-based limiting. It would be fine to shut off the port output and flash the power light if the total available budget is exceeded. Without that, this becomes a single-port PoE passthrough, not the two port its advertised as.
Jim Kusznir
Palouse Technology Services
(who is now returning 3 of these devices just purchased, as they are useless as currently implemented)
... View more
See more ideas labeled with:
-
Smart Managed Plus Switch
Submitted on
2016-10-19
03:11 AM
Submitted by
inky
on
2016-10-19
03:11 AM
I've had an unfair share of trouble when trying to restore saved configuration files (.cfg config) to GS108Ev2 running firmware 1.00.12. Eventually, I gave up and reprogrammed 3 switches from scratch. I had to go through the whole building to locate them. Brought with myself a laptop and had a phone handy to talk to a guy in the control room.
I think I found out what happened: Older versions of the Plus Utility do not support the password encryption required by V1.00.10 firmware. The old config files had unencrypted passwords (I checked with a hex editor). The new firmware expects its password encrypted, so it couldn't load the old password. I was locked out of the switches.
A cleartext header in the config file could help, so the switch (or the user!) knows which firmware version saved the config. If you want to make it really functional, have the firmware perform appropriate checks at load (restore) time, so old unencrypted passwords keep on working on new firmware versions.
... View more
See more ideas labeled with:
-
Smart Managed Plus Switch
I own an XS724EM 24-port 10G switch. It runs warm to the touch, and the default fan profile seems to err on the side of low noise rather than cooling. Tech support says that the switch is designed to spin down fans entirely unless a certain temperature threshold is reached. Personally, I would prefer to see more aggressive cooling, even if meant slightly more fan noise. So my feature request is twofold: Basic temperature monitoring (ambient, internal) in the admin GUI. All I want is a simple readout of how warm the switch currently thinks it is. Basic manual fan control in the admin GUI. I'm envisioning something like the "Cool/Balanced/Quiet" drop-down menu (see image) found on ReadyNAS units. I know the managed switches have functionality along these lines. To me, this basic temperature monitoring and control seems like it should definitely be included on Smart/Plus switches too.
... View more
See more ideas labeled with:
-
Insight Switch
-
Smart Managed Plus Switch
-
Smart Switch
I've just added a GS105Ev2 to my network, to add to an existing GS116Ev2. I am very disappointed to see that the 105 does not support a port description field which is present in the 116. Can this not be added? GS105Ev2 Firmware V1.6.0.6
... View more
See more ideas labeled with:
-
Smart Managed Plus Switch
Many NTGR business products still have SSL 2.0 and 3.0 and TLS 1.0 as options - nowadays these are obsolete and should be removed, TLS 1.2 is in the field for more then 10 years, so there should be no more prehistorical Web browser still requiring anything different.
... View more
See more ideas labeled with:
-
Insight Switch
-
Nighthawk Switch
-
Smart Managed Plus Switch
-
Smart Switch
Status:
New Idea
Submitted on
2018-12-18
02:01 PM
Submitted by
robertpankrath
on
2018-12-18
02:01 PM
Dear developers,
it would be great to be able to configure VLAN for management only.
See also this thread:
https://community.netgear.com/t5/Smart-Plus-Click-Switches/GS108Ev3-Cannot-set-VLAN-for-management-interface/td-p/971240
If that is too much work could you please implement the possibility to disable Webif with Plus Utility?
Reason for this is to get rid of this limitation /unpleasant behaviour:
"To support WEB GUI, all HTTP packets are forwarded to the embedded CPU. With Flow Control enabled, throughput will be impacted if the rate is higher than the CPU can handle."
or at least having a workaround to avoid it!
Kind Regards
Robert Pankrath
Berlin Germany
... View more
See more ideas labeled with:
-
Smart Managed Plus Switch
GS116Ev2 firmware 2.6022 or later
Request features:
IPv6 full function
IEEE 802.3ad (LACP) dymanic as well as static.
... View more
See more ideas labeled with:
-
Smart Managed Plus Switch
I've just added a GS108Ev3 to my network with existing GS116Ev2 and GS105Ev2. I am very disappointed to see that the 108 does not support a port description field which is present in the 116 and 105. Can this be added please? GS108Ev3 Firmware V2.06.17GR see also https://community.netgear.com/t5/Idea-Exchange-For-Business/Add-Port-descripton-to-GS105Ev2-in-GS116Ev2-it-is-present/idi-p/2009767
... View more
See more ideas labeled with:
-
Smart Managed Plus Switch
Status:
New Idea
Submitted on
2020-12-27
11:19 PM
Submitted by
nismo9132_net
on
2020-12-27
11:19 PM
I purchased both a GS305E and two GS308E switches and really like the performance and configuration functionality, but it's missing a key feature -a Configurable Management VLAN. Please add this feature because otherwise I'm likely going to return these switches to get something that supports them from another vendor for the same price point.
... View more
See more ideas labeled with:
-
Smart Managed Plus Switch