Showing ideas with label Smart Switch.
Show all ideas
Submitted on
2017-07-12
08:14 PM
Submitted by
bwayspork
on
2017-07-12
08:14 PM
Just wanted to put this in as a formal request after speaking with support. On this switch, and apparently almost all others in the current lineup, if you lose your password, you're out of luck. The only option to gain access is a factory reset. This of course wipes the config as well.
As anyone working in SOHO IT can tell you, it's very common to find a business going through multiple IT vendors/employees. So it's quite common to find a piece of equipment, have physical access to it, and have a need to reset the password. And in many cases, the configuration might ONLY be documented on the device itself. Reseting could lead to downtime as the new IT folks figure out what the config was.
Can Netgear consider some option (like "hold normal reset button for X seconds") to reset only the password?
... View more
See more ideas labeled with:
-
Smart Switch
Most Smart Managed Pro including cloud manageable switches (many more than the ones tagged) offer a comprehensive list of DoS checks to enable/disable individually. It does not help much just showing that a port was shut down due to DoS. We need much more information on the DoS event detected in the logs. We had several reports and queries in the community on why ports were shut down unexpectedly. ....
... View more
See more ideas labeled with:
-
Insight Switch
-
Smart Switch
We're missing the ability to generate CSRs with 2048 bit on the Netgear Business products (like the Smart Manged Plus, Smart Managed Pro, Managed Switches, coming-up Routers like the BR500, and solo the ability to generate self-signed certificates accordingly.
... View more
See more ideas labeled with:
-
Insight AP
-
Insight Switch
-
Nighthawk Switch
-
Smart Switch
I want to make a time schedule for one POE port from 20:00 to 8:00 next day it should be disabled. This is now not possible. I have to make two schedules one from 20:00 to 23:59 and one from 0:00 to 8:00 but does not give the intende result since from 23:59 to 0:00 the port goes on. This because 24:00 is nota valid value and in fact it has to be valid.
Other option could be set with the schedule is the port has to switched of or on then the rule could be from 8:00 to 20:00 switch the port on other time switch it of . repeat this for every day.
... View more
See more ideas labeled with:
-
Smart Switch
Hi, The lack of L3 DHCP Relay on the S3300 switch is quite problematic. We're facing situations where a site is equipped with a router managed by third party. Ideally, we would like to cable the site with only a stack of S3300 switches but since they do not support L3 DHCP Relay, we would also have to include a router or server handling either direct or relayed DHCP. The S3300 can have a routing table, an L3 address and supports a default gateway.. Could the Netgear team look into adding the support for L3 DHCP Relay as well? Thanks, Justin
... View more
See more ideas labeled with:
-
Smart Managed Plus Switch
-
Smart Switch
We recently had to replace a GS752TP and we received a GS752TPv2. Support informed us that the GS752TPv2 is not fully supported in NMS300, which we use for schedule configuration backups. We would like to have support for this.
... View more
See more ideas labeled with:
-
Smart Switch
Submitted on
2016-10-11
09:27 AM
Submitted by
PAH
on
2016-10-11
09:27 AM
Hi,
It has been suggested that I submit this increased functionality request to improve the switches capability on its accessing frequency when updating its system time from an SNTP server.
Most other manufacturers allow access times up to 1000's of hours. I normally update various network appliances either once a day or once a month, which is fine for most instances. However, this doesn't appear possible with my GS724T switches. The maximum polling time results, in my case, with a Kiss Of Death response due to too many update requests. The only work around is possibly using a DNS access to an SNTP server pool, as opposed to accessing a fixed time server IP address.
I would have just put up with this problem but
DaneA from the NETGEAR Community Team suggested I raise this as a functionality request!
I did look into having my own SNTP server but the cost is prohibitive.
Regards PAH
Last update from the NETGEAR Community Team shown below for info.
: How do you set the update frequency when using an SNTP sever to synchronize time on a GS724T ...
Hi PAH,
Since there is no option to manually configure the frequency of when the GS724Tv3/4 will access the SNTP servers, I suggest that you post this concern as feature request in the Idea Exchange board for Business here. Be reminded that adding kudos to the ideas will help as the development team will be reviewing the post that has the most kudos and it might be considered to be added on the future functionality of the product.
Regards,
DaneA
NETGEAR Community Team
... View more
See more ideas labeled with:
-
Smart Switch
Status:
New Idea
Submitted on
2019-06-11
03:54 AM
Submitted by
Duncker-Munnikh
on
2019-06-11
03:54 AM
Hi, Having multiple M4100 and GSM7228 switches where device view is not working due to Java support in the webbrowser. Althought there should be a work arround with installing an old java and using IE11 this is not an ideal solution. I had simular issue with HP 2910 switches, HP made a new Aruba firmware for this switch and is now fully web-managed. I see a lot of people with the same issue in the ICT businnes with no proper solution. Spending € 1400 for a new switch which require an old Java is not done. Kind regards, Steven
... View more
See more ideas labeled with:
-
Smart Switch
Customers of Smart Managed Pro switches always experience problems when migrating from smaller to bigger switches, when a warranty exchange does provide a newer model, ...
All Smart Managed Pro switches must use the same configuration file and logic, old config files must be workable on newer switches.
... View more
See more ideas labeled with:
-
Smart Switch
Status:
New Idea
Submitted on
2019-03-04
01:02 AM
Submitted by
stefaanbolle
on
2019-03-04
01:02 AM
Add SNMP monitoring capabilities to the JGS516PE switch
... View more
See more ideas labeled with:
-
Smart Switch
Having recently (less than 18 months) deployed multiple GS728TPP switches, and now deploying new offices with the Insight management series, it would be great to have a firmware update to allow these older switches to be managed.
I would be willing to pay for the firmware upgrade for this functionality! (rather than have to replace each switch!)
... View more
See more ideas labeled with:
-
Insight Mobile App
-
Insight Web Portal
-
Smart Switch
All of the netgear products we have tested do not support TLS 1.2 and have out of date cyphers.
Fix it please. The rest of the industry already has
... View more
See more ideas labeled with:
-
Managed Switch
-
Smart Managed Plus Switch
-
Smart Switch
When trying to set a global timer schedule on a FS728TLP switch it looks like you are unable to set schedules that stretch beyond the 'Shutdown Time Start' of the 'Date Start' field. (attaching screenshot of error message)
An example of the situation one of customers would like to utilise:
We would like to have the PoE ports power off for the evening and come back online the following morning, i.e. ports should power down at 4pm in the evening and come back online the following morning at 7am.
This is not possible with this caveat that exists on the FS728TLP switch. The FS728TPv1 and FS728TPv2 are capable of setting these requirements.
Can this feature be added for the FS728TLP switch?
... View more
See more ideas labeled with:
-
Smart Switch
Hi There, can I asked to fix the Mikrotik Romon in all of your Switches, I saw its fixed for M4200 and M4300 not for M4100 and others, Thanks.
... View more
See more ideas labeled with:
-
Managed Switch
-
Smart Switch
Submitted on
2017-08-21
03:59 PM
Submitted by
ccaudle
on
2017-08-21
03:59 PM
The 802.1AS firmware for the GS724T switch already handles almost everything needed for full 1588 support, it would be useful to add the capability to use layer 3 transport for the 1588 timestamps so that the GS switch could work as a 1588 transparent clock in IP based systems, not just layer 2 802.1AS transport.
... View more
See more ideas labeled with:
-
Smart Switch
Submitted on
2017-08-20
10:14 AM
Submitted by
Tonkinite
on
2017-08-20
10:14 AM
The XS series switches only support L2 hashing with LACP (802.3ad), apparently only the managed switches support anything beyond L2. The ReadyNAS units support L2, L2+L3, and L2+L3+L4 out of the box.
Could the upper tier web managed switches please have at least L2+L3 support added? I'm not talking about going crazy and adding more than that. Should be a relatively minor change, the UI changes would likely be more involved than the protocol changes.
It should be a big benefit to the ReadyNAS users.
... View more
See more ideas labeled with:
-
Smart Switch
Submitted on
2017-06-13
07:37 AM
Submitted by
toilatoi71312
on
2017-06-13
07:37 AM
Hi dear,
I have read much more model of layer 2/3 smart switch. I hope have funtion like this:
http://documentation.netgear.com/gs108t/enu/202-10337-01/GS108T_UM-07-05.html
Please guild me if this model have this, or we can have it in future.
Thanks & Best Reagard.
... View more
See more ideas labeled with:
-
Smart Switch
Submitted on
2016-06-30
01:46 PM
Submitted by
fcharr75
on
2016-06-30
01:46 PM
I would suggest you the following changes for the next firmware :
IGMPv3
MLDv2
DoS less sensitive
for modern IPTV set-top boxes.
THANK YOU !
... View more
See more ideas labeled with:
-
Smart Switch
web gui is very confusing and if you dont know netgear much you dont find settings like dns etc quickly. so add a search option (javascript, browserside) which allows to quickly search in an index the setting page.. so searching for "dns" will show me the page where i can set dns settings. also add option to quickly open context in cli on each page, so i can click a button which shows this context part in cli, which can be edited in browser like notepad or sth else. or a small cli popup.
... View more
See more ideas labeled with:
-
Smart Switch
as we all dislike downtimes we need a simple restart if updating to a new firmware. a) just switchover during run if change is quite simple and restart some services b) restart but keep on switching but just do some basic things like vlan etc if this is possible by hardware. means a kind of fallback switching if cpu is restarting, many tasks shouldnt need cpu. c) add an option to restart switch without letting ports go down so server wont notice downtime. so they will just timeout i know these ideas are not really useful, but maybe an inspiration in optimizing the update downtime. also a faster reboot could be nice without all h/w inis. also reboot should be timed on special countdown in minutes or on special time/date setable over html GUI. so it can be planned. also if boot fails it should recover to old fw, for doing so it should force user to login to web gui and say ok worked otherwise it would reboot to old fw
... View more
See more ideas labeled with:
-
Smart Switch