I had opened a ticket asking for the ability to trunk multiple vlans out a single port to allow easier management of devices on each vlan, this seems like its not possible today, the alternative to this request is to just install SSH on the router. With SSH enabled on the router I can create dynamic tunnels through the router to the other networks without even needing to make any port changes. I am actually shocked that the orbi only supports Telnet, there is no reason in 2022 that the only CLI management is Telnet. Dropbear is already installed on the device, we should be allowed to choose SSH or telnet.
... View more
See more ideas labeled with:
Status:
New Idea
Submitted on
2020-10-29
11:08 AM
Submitted by
Edouard_BERNARD
on
2020-10-29
11:08 AM
Hello, the DHCP server is a bit "basic". Would it be possible to integrate some Options in the BR500 router and be able to manage them in the Insight portal. This would be a great advantage to maintain small sites with SIP phones. Option 2 (Time Zone Offset) Option 4 (Time Server) Option 60 (vendor ID) Option 66 (TFTP or HTTP server in stringvalue) Option 114 (URL) Option 120 (P-CSCF address) Thank You, Edouard
... View more
See more ideas labeled with:
Netgear Insight, although I think targeted toward businesses, does not support compliant WPA2 Enterprise. It forces TKIP+AES mixed mode. It is impossible to enforce WPA2 Enterprise on an Insight managed device. The devices are capable, but you have to unmanage a device and set CCMP-AES manually on the local interface, and that AP can never be managed by Insight, or it will change the encryption from AES back to TKIP+AES mixed mode.
... View more
See more ideas labeled with:
Status:
Implemented In Latest Product
Submitted on
2021-02-15
03:25 PM
Submitted by
JM520
on
2021-02-15
03:25 PM
When I bought this business class mesh system about a year back (1 router and 2 satellites), tech support stated that the product being a business producr does not have a built in firewall and I should procure an external firewall. A year back tech support stated that vlan segmentation and vlan to ssid mapping would be coming in a later release. At this point indeed the feature came in a later release of hardware in AX6000. I was talking to tech support today again as I purchased a decent hardware firewall and I would like to have the same vlan feature Iin the AX6000) of vlan 1,10,20 and 30 married to SSID with trunking available on the AC3000 as this should be basic network fiormware/software update and has nothing to do with wifi6 which may demand a new chipset. In the very least I need to segment the IOT stuff from business traffic. Can you please integrate proper vlan/ssid mapping into the AC3000 (SRR60). The way this should work is a user joins SSID Wireless 1 and should be part of the corresponding VLAN/Subnet and the AC3000 would run in AP mode and trunk (80-2.1q) the vlans via the WAN port to the Firewall which provides the IP routing, dhcp and all other services. I am not looking for wifi-6.
... View more
See more ideas labeled with:
It would be really useful to be able to configure DHCP Snooping features within the web or mobile interfaces. Certain scenarios involving DHCP just make using managed mode impossible.
... View more
See more ideas labeled with:
Status:
Comments Requested
Submitted on
2022-04-04
12:51 PM
Submitted by
EReese3
on
2022-04-04
12:51 PM
Need a replacement for the BR200 and BR500 and quickly! one location is maxed out on 1gb fiber and would like to go faster and have the site to site function actually work as orginaly advertised for the BR500. Also need the LAN ports to be be fiber
... View more
See more ideas labeled with:
Please look to add Port Description naming to the gs305e managed switch. With lots of devices and switches using port numbers is cumbersome.. names would be more efficient to manage.
... View more
See more ideas labeled with:
Please change the local device login page, to contain the device name. It would be immensely helpful to ensure I am logging into the correct device. Right now you only display the model in the right corner.
... View more
See more ideas labeled with:
Status:
New Idea
Submitted on
2020-06-27
01:56 PM
Submitted by
ArloPowerUser
on
2020-06-27
01:56 PM
I recommend that Netgear allow the Orbi Pro models to the ability to disable wifi radios at user's option for the following reasons: Simple update for Netgear/Orbi - Currently, Orbi software allows wifi radio strength choices of 100%, 50%, 25%...they should add an option for 0%/Off. It woudn't cost Netgear anything to provide the 0%/Off option as it only requires a modification to an existing field. It provides the User the option/choice rather than Netgear/Orbi making the choice for the user. Netgear/Orbi should place security as one of their highest priorities, and providing this option would reflect that as ethernet-only wired systems are generlly more secure than wifi. Netgeat provides this option on almost all of their other routers, so why not provide consistency and allow this as an option and give the user the same flexibility as other competing routers such as TP-Link, Linksys, and Asus. Consequently, I don't understand the resistance to doing so as it's an easy fix, increases security, and provides users the same option they have with other competing routers. Since you already provide an option for radio strength down to 25%, why not add an addtional selection for 0%/Off? Some users only use wifi occaisionally or alternatively would like to occaisoinaly diable wifi for security and/or interference reasons, and such an option would allow users to so turn it on when needed, and off when not needed. Wifi is not as secure in dense city areas and sometimes creates interference with other devices/systems, thus it would be prudent to allow the user to have the option to disable the wifi radios when needed...just give the user the choice.
... View more
See more ideas labeled with:
Submitted on
2018-01-23
03:09 AM
Submitted by
Greg75
on
2018-01-23
03:09 AM
It would be very usefull to be able to reboot online from the interface especially when remotely managing. Being able to change the wifi power would be great too but this is more complex
Hopefully in a future firmware
Thanks
... View more
See more ideas labeled with:
I've just added a GS105Ev2 to my network, to add to an existing GS116Ev2. I am very disappointed to see that the 105 does not support a port description field which is present in the 116. Can this not be added? GS105Ev2 Firmware V1.6.0.6
... View more
See more ideas labeled with:
Seems like we only have an all or nothing choice: "Allow IoT devices to see each other and access my local network" If I allow this then the whole purpose of the seperate SSID for IoT is lost. I want the IoT devices to see each other, but NOT access my local network. Specifically I have a Hubitat hub which needs to talk to two Android tablets, two Konnected boards and some TVs. They are all on the same SSID, and I would like them to stay removed from my local network. Seems the newer WiFi 6 router allows this to be configured via VLAN. Personally I'd prefer a method whereby access levels could be granted on a device by device basis. Thank you
... View more
See more ideas labeled with:
I would like to upload my own certificate to web interface and be able to use my own domain name
... View more
See more ideas labeled with:
Submitted on
2015-08-21
01:26 AM
Submitted by
cuvillier
on
2015-08-21
01:26 AM
Hi ,
When do you plan to implement this application wifi analytics on ios ?
My ipad would like it, my iphone also, I will accept to pay for this application
please include the rogue detection
regards
Philippe CUVILLIER Orange Presales Engineer
... View more
See more ideas labeled with:
When building a guest network in Insight, it's important to be able to rate limit throughput per client so that no one client can consume all available bandwidth on that SSID/vLan. It can be accomplished via QoS on the APs themselves, but Inisght will not recognize those configs and the config change wouldn't be replicated to other APs. Additionally, the QoS config may be destroyed by Inisght upon config updates. Instructions for configuring QoS at the AP level: https://community.netgear.com/t5/Business-Wireless/How-do-I-limit-bandwidth-per-device-on-a-WAC730/m-p/1767103
... View more
See more ideas labeled with:
Status:
New Idea
Submitted on
2021-12-23
09:45 AM
Submitted by
milkfromstone
on
2021-12-23
09:45 AM
What if we could have a superuser network that could cut across network isolation? Scenarion: - wireless 1: owner's network (superuser) - wireless 2: a network for guests, with network isolation Disired outcome: - How can wireless 1 see devices on wireless 2? - How can we ensure wireless 2 has no visibility of devices on wireless 1? I want W2 guests to be able to access Sonos, lights, fans that would be on W2, but not devices set on W1. All this while enabling W1 (superuser) to see IoT devices on any network.
... View more
See more ideas labeled with:
Submitted on
2017-07-04
09:50 PM
Submitted by
kabigears
on
2017-07-04
09:50 PM
These Plus switch web interface can only be accessed from the default VLAN 1. This is restrictive. Could a future firmware include the ablility to access the web interface from all defined VLAN's on the switch and not only VLAN 1.
... View more
Status:
New Idea
Submitted on
2022-10-25
05:17 AM
Submitted by
classicsound
on
2022-10-25
05:17 AM
Hello, I am just starting to work with the AV Line switches. I use them in a concert hall. There is an administrator and many users running the shows. For this, from my point of view, there needs to be some kind of user management. On the one hand, of course, the administrator with full access, but on the other hand, another account for status monitoring and assigning ports to VLANs, if that is necessary for a show. A user management with rights management would be perfect for this. Is such a feature already planned?
... View more
See more ideas labeled with:
In the client section of the Insight App, it would be useful to see additional information against each device, for instance, which channel frequency are they using 2.4 to 5Ghz, what channel are they using, what 802.11xx mode are they using, what WPA mode did they authenticate with, the RSSI signal strength, are they using a private MAC address (on a modern phone) - adding fields (and others) such as these into the Client's page would help with diagnosing connection problems. Also would be good to be able to click on a client in the browser and see its history, so when it connect, disconnect, change AP if roamed, connect again etc, so we can see a history of the wireless client with relevant fields that will allow us to diagnose connectivity problems.
... View more
See more ideas labeled with:
Limiting the antenna power to levels like 100%, 50%, 25%, etc. is ridiculous and severly limits fine tuning it to the local radio enviroment. Please update to allow changing it to values from 1 dBm to 18 (20) dBm like a normal person.
... View more
See more ideas labeled with: