Reply
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
G1010USB (CostCo)
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
2012-02-06
08:40 PM
2012-02-06
08:40 PM
G1010USB (CostCo)
Not working with my ReadyNAS Ultra 4. The UI says there is no UPS attached but looking in the syslog I see:
Feb 6 22:38:45 chief kernel: generic-usb 0003:09AE:2010.3030: hiddev0: USB HID v1.10 Device [Tripp Lite Tripp Lite UPS ] on usb-0000:00:1d.0-2/input0
Feb 6 22:39:00 chief kernel: usb 5-2: USB disconnect, address 115
Feb 6 22:39:00 chief kernel: usb 5-2: new low speed USB device using uhci_hcd and address 116
Feb 6 22:39:00 chief kernel: generic-usb 0003:09AE:2010.3031: hiddev0: USB HID v1.10 Device [Tripp Lite Tripp Lite UPS ] on usb-0000:00:1d.0-2/input0
Feb 6 22:39:16 chief kernel: usb 5-2: USB disconnect, address 116
Feb 6 22:39:16 chief kernel: usb 5-2: new low speed USB device using uhci_hcd and address 117
Feb 6 22:39:16 chief kernel: generic-usb 0003:09AE:2010.3032: hiddev0: USB HID v1.10 Device [Tripp Lite Tripp Lite UPS ] on usb-0000:00:1d.0-2/input0
Feb 6 22:39:31 chief kernel: usb 5-2: USB disconnect, address 117
Feb 6 22:39:32 chief kernel: usb 5-2: new low speed USB device using uhci_hcd and address 118
Feb 6 22:39:32 chief kernel: generic-usb 0003:09AE:2010.3033: hiddev0: USB HID v1.10 Device [Tripp Lite Tripp Lite UPS ] on usb-0000:00:1d.0-2/input0
Feb 6 22:39:47 chief kernel: usb 5-2: USB disconnect, address 118
Feb 6 22:39:47 chief kernel: usb 5-2: new low speed USB device using uhci_hcd and address 119
This is using RAIDiator 4.2.19
Feb 6 22:38:45 chief kernel: generic-usb 0003:09AE:2010.3030: hiddev0: USB HID v1.10 Device [Tripp Lite Tripp Lite UPS ] on usb-0000:00:1d.0-2/input0
Feb 6 22:39:00 chief kernel: usb 5-2: USB disconnect, address 115
Feb 6 22:39:00 chief kernel: usb 5-2: new low speed USB device using uhci_hcd and address 116
Feb 6 22:39:00 chief kernel: generic-usb 0003:09AE:2010.3031: hiddev0: USB HID v1.10 Device [Tripp Lite Tripp Lite UPS ] on usb-0000:00:1d.0-2/input0
Feb 6 22:39:16 chief kernel: usb 5-2: USB disconnect, address 116
Feb 6 22:39:16 chief kernel: usb 5-2: new low speed USB device using uhci_hcd and address 117
Feb 6 22:39:16 chief kernel: generic-usb 0003:09AE:2010.3032: hiddev0: USB HID v1.10 Device [Tripp Lite Tripp Lite UPS ] on usb-0000:00:1d.0-2/input0
Feb 6 22:39:31 chief kernel: usb 5-2: USB disconnect, address 117
Feb 6 22:39:32 chief kernel: usb 5-2: new low speed USB device using uhci_hcd and address 118
Feb 6 22:39:32 chief kernel: generic-usb 0003:09AE:2010.3033: hiddev0: USB HID v1.10 Device [Tripp Lite Tripp Lite UPS ] on usb-0000:00:1d.0-2/input0
Feb 6 22:39:47 chief kernel: usb 5-2: USB disconnect, address 118
Feb 6 22:39:47 chief kernel: usb 5-2: new low speed USB device using uhci_hcd and address 119
This is using RAIDiator 4.2.19
Message 1 of 4
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
2012-02-13
06:26 AM
2012-02-13
06:26 AM
Re: G1010USB (CostCo)
Should I post this in another forum for help getting the UPS working?
Message 2 of 4
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
2012-02-13
06:36 AM
2012-02-13
06:36 AM
Re: G1010USB (CostCo)
You could try opening a support ticket. Not sure if they can resolve it though.
edalquist wrote: Should I post this in another forum for help getting the UPS working?
Message 3 of 4
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
2012-02-13
02:03 PM
2012-02-13
02:03 PM
Re: G1010USB (CostCo)
I'll look into doing that.
I did find this: http://comments.gmane.org/gmane.comp.mo ... .user/6546 it implies that the UPS is supported as of NUT 2.6, the fact that the ReadyNAS is using NUT 2.0.5 doesn't give me much hope though 🙂
I did find this: http://comments.gmane.org/gmane.comp.mo ... .user/6546 it implies that the UPS is supported as of NUT 2.6, the fact that the ReadyNAS is using NUT 2.0.5 doesn't give me much hope though 🙂
Message 4 of 4