- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
Re: WAN link instability MR60 / MK63 with firmware V1.1.6.122
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello,
I noticed a concrete instability of the internet connection with the recent firmware version V1.1.6.122 in my Nighthawk MR60 and satellites MS60 (MK63).
The MR60 router is cascaded to a ISP's router but this configuration has worked for me for 12 months without problems.
The only changes were the firmware updates: with the latest the whole system became unstable.
At first I solved it with MR60 reboots when the problem often repeated itself.
The serious symptom is that on reaching the web interface the internet connection was marked "Offline" while my ISP's router works perfectly.
Now I'm back to firmware V1.0.6.116_2.0.54 and I'm not experiencing problems.
The other anomaly of the firmware version V1.1.6.122 that I noticed is on the Netgear Nighthawk android app: I could no longer see the detail of the access point (MR60 or the two MS60s) used by the clients.
Anyone have the same problems?
Solved! Go to Solution.
Accepted Solutions
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Have you tried correcting the double nat issue?
A double nat happens when you cascade more than 1 router.
https://kb.netgear.com/30186/What-is-Double-NAT
Fixes? There’s 3 options but only use 1.
1. Put the modem/gateway in modem only/pass through mode. This disables its routing functions.
2. Leave the modem/gateway in router mode but put the Netgears IP address into its DMZ. This forwards the data to the netgear. You can either leave the modem/gateway’s wireless enabled or disabled. Just make sure its using a different wifi channel to prevent interference
3. Put the Netgear into access point mode. This disables its routing functions. Wifi/ethernet still works but it does disable some features.
https://kb.netgear.com/26765/Which-features-are-disabled-on-my-NETGEAR-router-when-it-is-set-to-AP-M...
All Replies
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Have you tried correcting the double nat issue?
A double nat happens when you cascade more than 1 router.
https://kb.netgear.com/30186/What-is-Double-NAT
Fixes? There’s 3 options but only use 1.
1. Put the modem/gateway in modem only/pass through mode. This disables its routing functions.
2. Leave the modem/gateway in router mode but put the Netgears IP address into its DMZ. This forwards the data to the netgear. You can either leave the modem/gateway’s wireless enabled or disabled. Just make sure its using a different wifi channel to prevent interference
3. Put the Netgear into access point mode. This disables its routing functions. Wifi/ethernet still works but it does disable some features.
https://kb.netgear.com/26765/Which-features-are-disabled-on-my-NETGEAR-router-when-it-is-set-to-AP-M...
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: WAN link instability MR60 / MK63 with firmware V1.1.6.122
Hello,
I've again upgraded firmware of my MR60 and Satellites of my Mesh wi-fi to version V1.1.6.122 and implemented the proposed solution n. 2.
I need to wait at least a week to see if my problem recurs.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: WAN link instability MR60 / MK63 with firmware V1.1.6.122
Hope it works for you!
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: WAN link instability MR60 / MK63 with firmware V1.1.6.122
I confirm: eliminating the "Double NAT" and putting in the DMZ on the ISP provider modem my MR60 I had no more disconnection problems.
Thank you for you help.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: WAN link instability MR60 / MK63 with firmware V1.1.6.122
Glad its working for you!
If you mark the solution as solved, it might help the next person with that issue.
I normally don't say make a backup, but if I don't someone else will for "extra credit"
A backup is good just in case you run into issues now that you have it setup properly.
• What is the difference between WiFi 6 and WiFi 7?
• Yes! WiFi 7 is backwards compatible with other Wifi devices? Learn more