Reply

Re: New - XR450/XR500 Firmware Version 2.3.2.134 Released

Raf1212
Luminary

Re: New - XR450/XR500 Firmware Version 2.3.2.134 Released

@agents no, say it of the holder of those who got kicked out 300 euros for a router that is not working properly, a long time do not use this scrap, but others that may want to because they can not afford to different hardware, so do not slacken, because it takes already two or three years .
Message 51 of 59
agent47isn1
Luminary

Re: New - XR450/XR500 Firmware Version 2.3.2.134 Released

I did this is a public forum plus I have the xr450 which is just like the xr500 minus small differences. Ive only had a few hiccups but for the majority of 2 years this router has been nothing short of amazing.
Message 52 of 59
Himaro0
Luminary

Re: New - XR450/XR500 Firmware Version 2.3.2.134 Released

Hello,

 

Still getting QOS error: device not found 

 

Things tried:

Downgrade back to version .130 and did a hard reset, upgraded to version .134

 

The connection benchmark does not match the actual number IPS speed number. 

 

Any thoughts? 

 

Thanks

Message 53 of 59
Netduma-Liam
NetDuma Partner

Re: New - XR450/XR500 Firmware Version 2.3.2.134 Released

Could you please repeat the process but instead downgrade to the 114 firmware, linked below.

https://kb.netgear.com/000062867/XR500-Firmware-Version-2-3-2-114

Once downgraded factory reset either through the interface or by holding the button on the back for thirty seconds.

 

Then re-upgrade and don't factory reset after the upgrade.

Message 54 of 59
domino138
Luminary

Re: New - XR450/XR500 Firmware Version 2.3.2.134 Released

Hi Liam - do you have any idea when the next version is coming out for the XR500 please?

Message 55 of 59
Netduma-Fraser
NetDuma Partner

Re: New - XR450/XR500 Firmware Version 2.3.2.134 Released

@domino138 we post any and all potential updates on the status of firmware here: http://support.netduma.com/en/support/solutions/articles/16000132677-dumaos-firmware-progress outside of that we don't have any extra information to give
Message 56 of 59
lenbo7777
Luminary

Re: New - XR450/XR500 Firmware Version 2.3.2.134 Released

My XR500 had a problem - documented here:

...where it would sporadically restart and reset.  Since upgrading to .134, I haven't experienced this again.  But I also hadn't reserved any addresses.  Earlier this week, I reserved one device and address in the LAN.  My DHCP is set to 192.168.1.2 - 254.

 

The morning after I made the reservation, my router restarted and reset - just like it had previously.  

 

Is anyone else experiencing this...and is there ever going to be any relief?

Message 57 of 59
FURRYe38
Guru

Re: New - XR450/XR500 Firmware Version 2.3.2.134 Released

I recommend that you leave the DHCP IP address pool range set to a smaller range. You don't have to use the default range. I personally never use the factory range on any NG router. Also this provides room for static IP addressed devices as well. I use .100 to .150 as I only have around 30 devices. Plenty of room for additional devices if and when that happens. 

 

We hope so, however don't have that info. 

My Setup ISP SparkLight | Internet Cable 1000↓/50↑ CM1200 Modem |  Wifi Router Orbi RBK752 (Router Mode), Wired Backhaul and R8500 | Switches NG GS105/8, GS308v3, GS110MX and XS505M | 

Additional NG HW: C7800/CAX80/CM1100/CM1200/CM2000, Orbi: CBK40, CBK752, RBK50, RBK853, RBK752, RBK953, SXK30 | NightHawk: R7000, R7800, R7960P, R8000, R8500, RAXE500, RAX50, XR450, EX7500/EX7700

Message 58 of 59
Netduma-Liam
NetDuma Partner

Re: New - XR450/XR500 Firmware Version 2.3.2.134 Released

That is odd, I would suggest going through and reserving IP addresses outside the DHCP range, then see if you experience any further disconnections after that.

Message 59 of 59
Discussion stats
Announcements

Orbi WiFi 6E