- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
Re: R6400v2 Firmware Version 1.0.4.1.120
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
R6400v2 Firmware Version 1.0.4.1.120
This firmware has caused the same issue as described in the following discussion:
The symptom is that you get a page "This site can't be reached", then it will try to reload the page and is usually successful. Some times you have to manually reload the page for it to load.
This needs to be addressed as soon as possible. It would be appreciated to get a reply when this issue has been acknowledged and corrected. In the meantime, I'm downgrading to version 1.0.4.106, which was working properly.
Thank you.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: R6400v2 Firmware Version 1.0.4.1.120
quite a few posts on this issue across multiple product lines.
Thanks for posting.
Hopefully the more posts, the more mods that see it and direct the engineering teams at it
also in AP setup: RAXE500->EAX80
1.4gig download/100mbps upload from Xfinity
We’re members of the public helping out on our own time.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: R6400v2 Firmware Version 1.0.4.1.120
Please post about this here for your model router:
https://community.netgear.com/t5/General-WiFi-Routers-Non/bd-p/home-wifi-routers-general
Good Luck.
@JDCDR wrote:
This firmware has caused the same issue as described in the following discussion:
The symptom is that you get a page "This site can't be reached", then it will try to reload the page and is usually successful. Some times you have to manually reload the page for it to load.
This needs to be addressed as soon as possible. It would be appreciated to get a reply when this issue has been acknowledged and corrected. In the meantime, I'm downgrading to version 1.0.4.106, which was working properly.
Thank you.
My Setup | ISP SparkLight | Internet Cable 1000↓/50↑ CAX80 Modem Mode | Wifi Router RBKE963 and RBE973 | Switches NG GS105/8, GS308v3, GS110MX and XS505M | Additional NG HW: C7800/CAX30/CAX80/CM1100/CM1200/CM2000, Orbi: CBK752, RBK50, RBK853, RBK752, RBK953, SXK30 | NightHawk: MK63, MK93S, R7000, R7800, R7960P, R8000, RAXE500, RAX120v2, RAX50v2, XR450/500/700/1000,
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: R6400v2 Firmware Version 1.0.4.1.120
Same issues. I downgraded back to V1.0.4.106_10.0.80 since the latest firmware as of this writing was causing the timeout issues as many have mentioned. According to my family the internet went out a couple of times.
I complained to Netgear about it on Twitter and after a couple of days they responded that they wanted to contact me about the issue. Well, considering that I mentioned that there's posts in the community forum, honestly they could just check here instead.
I plan to go back to ASUS when I get the funds to replace this router.
• What is the difference between WiFi 6 and WiFi 7?
• Yes! WiFi 7 is backwards compatible with other Wifi devices? Learn more