- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
R7000P Bricked. Accepts TFTP from Serial Cable but Will Not Load Properly
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
R7000P Bricked. Accepts TFTP from Serial Cable but Will Not Load Properly
R7000p bricked after a botched firmward update.
I can access the CFE via serial cable through Putty. After nvram erase, the device accepts tftp and a transfer of the latest firmware "r7000p-v1.3.2.134_10.1.66.chk" is successful via windows tftp. However, then the device just continues to cycle through its startup and not successfully run the new firmware, displaying the following:
Decompressing...done
CFE for Foxconn Router R7000PLUS version: v1.0.4
Build Date: Fri Nov 4 14:55:02 CST 2016
Init Arena
Init Devs.
Boot up from NAND flash...
Bootcode Boot partition size = 524288(0x80000)
DDR Clock: 533 MHz
Info: DDR frequency set from clkfreq=1000,*533*
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 7.14.121 (r552363)
CPU type 0x0: 1000MHz
Tot mem: 262144 KBytes
Device eth0: hwaddr A0-04-60-6E-73-DE, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
Checking crc...Loader:raw Filesys:raw Dev:nflash0.os File: Optionsnull)
Loading: ..... 5467424 bytes read
Entry at 0x00008000
Closing network.
Starting program at 0x00008000
[ 2.480000] console [ttyS0] enabled, bootconsole disabled
[ 2.480000] serial8250.0: ttyS1 at MMIO 0x18000400 (irq = 117) is a 16550
[ 2.500000] brd: module loaded
[ 2.500000] loop: module loaded
[ 2.510000] pflash: found no supported devices
[ 2.510000] bcmsflash: found no supported devices
[ 3.220000] Boot partition size = 524288(0x80000)
[ 3.230000] lookup_nflash_rootfs_offset: offset = 0x200000
[ 3.230000] nflash: squash filesystem with lzma found at block 32
[ 3.240000] Creating 17 MTD partitions on "nflash":
[ 3.250000] 0x000000000000-0x000000080000 : "boot"
[ 3.250000] 0x000000080000-0x000000200000 : "nvram"
[ 3.260000] 0x000000200000-0x000006f00000 : "linux"
[ 3.260000] 0x00000041b348-0x000006f00000 : "rootfs"
[ 3.270000] 0x000007400000-0x000007480000 : "board_data"
[ 3.280000] 0x000007480000-0x000007580000 : "POT1"
[ 3.280000] 0x000007580000-0x000007680000 : "POT2"
[ 3.290000] 0x000007680000-0x000007940000 : "T_Meter1"
[ 3.290000] 0x000007940000-0x000007c00000 : "T_Meter2"
[ 3.300000] 0x000007c00000-0x000007c80000 : "ML1"
[ 3.310000] 0x000007c80000-0x000007d00000 : "ML2"
[ 3.310000] 0x000007d00000-0x000007d80000 : "ML3"
[ 3.320000] 0x000007d80000-0x000007e00000 : "ML4"
[ 3.320000] 0x000007e00000-0x000007e80000 : "ML5"
[ 3.330000] 0x000007e80000-0x000007f00000 : "ML6"
[ 3.340000] 0x000007f00000-0x000007f80000 : "ML7"
[ 3.340000] 0x000007f80000-0x000008000000 : "DebugMsg"
[ 3.350000] PPP generic driver version 2.4.2
[ 3.350000] PPP MPPE Compression module registered
[ 3.360000] NET: Registered protocol family 24
[ 3.360000] PPPoL2TP kernel driver, V0.17
[ 3.370000] tun: Universal TUN/TAP device driver, 1.6
[ 3.370000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 3.380000] usbcore: registered new interface driver cdc_acm
[ 3.380000] cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
[ 3.390000] usbcore: registered new interface driver usblp
[ 3.400000] csw_retry 100
[ 3.400000] Initializing USB Mass Storage driver...
[ 3.410000] usbcore: registered new interface driver usb-storage
[ 3.410000] USB Mass Storage support registered.
[ 3.420000] usbcore: registered new interface driver usbserial
[ 3.420000] USB Serial support registered for generic
[ 3.430000] usbcore: registered new interface driver usbserial_generic
[ 3.430000] usbserial: USB Serial Driver core
[ 3.440000] USB Serial support registered for GSM modem (1-port)
[ 3.440000] usbcore: registered new interface driver option
[ 3.450000] option: v0.7.2:USB Driver for GSM modems
[ 3.460000] USB Serial support registered for Sierra USB modem
[ 3.460000] usbcore: registered new interface driver sierra
[ 3.470000] sierra: v.1.7.16:USB Driver for Sierra Wireless USB modems
[ 3.470000] u32 classifier
[ 3.480000] Actions configured
[ 3.480000] nf_conntrack version 0.5.0 (3969 buckets, 15876 max)
[ 3.490000] IPv4 over IPv4 tunneling driver
[ 3.490000] GRE over IPv4 tunneling driver
[ 3.500000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 3.500000] TCP cubic registered
[ 3.500000] NET: Registered protocol family 10
[ 3.510000] lo: Disabled Privacy Extensions
[ 3.510000] tunl0: Disabled Privacy Extensions
[ 3.520000] IPv6 over IPv4 tunneling driver
[ 3.520000] sit0: Disabled Privacy Extensions
[ 3.530000] ip6tnl0: Disabled Privacy Extensions
[ 3.530000] NET: Registered protocol family 17
[ 3.540000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[ 3.540000] All bugs added by David S. Miller <davem@redhat.com>
[ 3.580000] Northstar brcmnand NAND Flash Controller driver, Version 0.1 (c) Broadcom Inc. 2012
[ 3.590000] NAND device: Manufacturer ID: 0x01, Chip ID: 0xf1 (AMD NAND 128MiB 3,3V 8-bit)
[ 3.600000] Spare area=64 eccbytes 56, ecc bytes located at:
[ 3.600000] 2 3 4 5 6 7 8 9 10 11 12 13 14 15 18 19 20 21 22 23 24 25 26 27 28 29 30 31 34 35 36 37 38 39 40 41 42 43 44 45 46 47 50 51 52 53 54 55 56 57 58 59 60 61 62 63
[ 3.620000] Available 7 bytes at (off,len):
[ 3.620000] (1,1) (16,2) (32,2) (48,2) (0,0) (0,0) (0,0) (0,0)
[ 3.630000] Scanning device for bad blocks
[ 4.340000] Options: NO_AUTOINCR,NO_READRDY,BBT_SCAN2NDPAGE,
[ 4.350000] Creating 2 MTD partitions on "brcmnand":
[ 4.350000] 0x000003400000-0x000006f00000 : "brcmnand"
[ 4.360000] 0x000006f00000-0x000007400000 : "OpenVPN"
[ 4.370000] SQUASHFS error: Xattrs in filesystem, these will be ignored
[ 4.380000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[ 4.400000] devtmpfs: mounted
[ 4.400000] Freeing init memory: 292K
[sighandler]: No more events to be processed, quitting.
[cleanup]: Waiting for children.
[cleanup]: All children terminated.
Restoring defaults...Reading board data...
WSC UUID: 0x2db3f8d54e2da7d63442d3cb19021c81
NTP synchronized date/time: Fri Mar 17 18:06:58 2017
MAC address of 1st STA connected: 20-16-D8-B2-80-1C
No RF parameters! Use default.
### main:1494 Set Normal Power!
Doing nvram commit by pid 1 !
done
Reading board data...
WSC UUID: 0x2db3f8d54e2da7d63442d3cb19021c81
NTP synchronized date/time: Fri Mar 17 18:06:58 2017
MAC address of 1st STA connected: 20-16-D8-B2-80-1C
No RF parameters! Use default.
### main:1494 Set Normal Power!
[ 11.680000] Initialise conn table 2048 entries
insmod: bcm57xx.ko: no module by that name found
Previous thread on this was unresolved:
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: R7000P Bricked. Accepts TFTP from Serial Cable but Will Not Load Properly
You can check with support if the unit is still under warranty. But it may be bricked if the TFTP is not working.
DarrenM
• Introducing NETGEAR WiFi 7 Orbi 770 Series and Nighthawk RS300
• What is the difference between WiFi 6 and WiFi 7?
• Yes! WiFi 7 is backwards compatible with other Wifi devices? Learn more