- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
Nighthawk(R) X4S R7800 - Can't Open Port 1935
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Nighthawk(R) X4S R7800 - Can't Open Port 1935
Hi there
I'm having problem with port forwarding on my router.
The port im trying to port forward is port 1935 on my local ip.
I can forward port 10823 used for multiplayer server in farming simulator and it works fine, people can then join my server.
I have the router after my fiber box from my provider, I can't access that (no webinterface, have to call them to make changes). But which is sat to brigde mode by my provider.
Im using Nginx RTMP server on my pc, to stream from my mobile (Streamlabs Mobile, Custom RTMP Settings) to my pc. Local it works (localip:1935/live + custom stream key), but when i do it from mobiledata it won't stream (publicIP:1935/live + custom stream key), as it says in all guides.
Firmware update is: V1.0.2.90
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Nighthawk(R) X4S R7800 - Can't Open Port 1935
Hi @FlicherDK, welcome to the community! We'd like to know the following.
How are you checking if the ports were successfully forwarded? What results are you getting?
Do you have UPnP enabled?
Has it worked before?
Have you tried any other firmware versions?
Dexter
NETGEAR Team
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Nighthawk(R) X4S R7800 - Can't Open Port 1935
What is the Mfr and model# of the Internet Service Providers modem/ONT the NG router is connected too?
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Nighthawk(R) X4S R7800 - Can't Open Port 1935
How are you checking if the ports were successfully forwarded? What results are you getting? - is there away to test the port? - I only tried the stream the RTMP server that used that port and can't connect
Do you have UPnP enabled? Yes
Has it worked before? - No, but i can open port to a game (Farming Simulator 22)
Have you tried any other firmware versions? With the one when i uptatede when i got the router a year ago.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Nighthawk(R) X4S R7800 - Can't Open Port 1935
What is the Mfr and model# of the Internet Service Providers modem/ONT the NG router is connected too? - It's a fiber box from Stofa called: Icotera i6851-00
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Nighthawk(R) X4S R7800 - Can't Open Port 1935
@FlicherDK wrote:
What is the Mfr and model# of the Internet Service Providers modem/ONT the NG router is connected too? - It's a fiber box from Stofa called: Icotera i6851-00
What you call a "fiber box" looks very much like a gateway. At least, that's what Google suggests.
Icotera i6851-00 - Google Search
If it has four Ethernet ports on the back that confirms it and you could be in "double NAT" territory, with two routers in your network.
@FURRYe38 asked the question because that makes all the difference to how your network operates.
You say this thing is in bridge mode and that the ISP has to control it. That's an odd arrangement. Might be worth confirming it with them.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Nighthawk(R) X4S R7800 - Can't Open Port 1935
This is a all in one gateway:
https://icotera.com/media/1458/i6850-ftth-gateway-datasheet_3_7.pdf
@FlicherDK wrote:
What is the Mfr and model# of the Internet Service Providers modem/ONT the NG router is connected too? - It's a fiber box from Stofa called: Icotera i6851-00
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Nighthawk(R) X4S R7800 - Can't Open Port 1935
Which tells us what?
@FURRYe38 wrote:
This is a all in one gateway:
https://icotera.com/media/1458/i6850-ftth-gateway-datasheet_3_7.pdf
@FlicherDK wrote:
What is the Mfr and model# of the Internet Service Providers modem/ONT the NG router is connected too? - It's a fiber box from Stofa called: Icotera i6851-00
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Nighthawk(R) X4S R7800 - Can't Open Port 1935
Double NAT condition.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Nighthawk(R) X4S R7800 - Can't Open Port 1935
@FURRYe38 wrote:
Double NAT condition.
See above.
But @FlicherDK reckons to have that covered.
I was trying to take it a bit further. Which is why I wondered what we are supposed to make of repeated information.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Nighthawk(R) X4S R7800 - Can't Open Port 1935
https://kb.netgear.com/30186/What-is-Double-NAT
https://kb.netgear.com/30187/How-to-fix-issues-with-Double-NAT
Couple of options,
1. Configure the modem for transparent bridge or modem only mode. Then use the NG router in router mode. You'll need to contact the ISP for help and information in regards to the modem being bridged correctly.
2. If you can't bridge the modem, disable ALL wifi radios on the modem, configure the modems DMZ/ExposedHost or IP Pass-Through for the IP address the NG router gets from the modem. https://kb.netgear.com/25891/DMZ-on-NETGEAR-routers
https://kb.netgear.com/24086/How-do-I-set-up-a-default-DMZ-server-on-my-Nighthawk-router
3. Or disable all wifi radios on the modem and connect the NG router to the modem, LAN to LAN configure AP mode on the NG router.
https://kb.netgear.com/24104/How-do-I-change-my-Nighthawk-router-to-AP-mode-after-I-ve-already-run-s...
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Nighthawk(R) X4S R7800 - Can't Open Port 1935
@FURRYe38 wrote:Double NAT condition.
See above.
But @FlicherDK reckons to have that covered.
I was trying to take it a bit further. Which is why I wondered what we are supposed to make of repeated information
It used be be used as a router, but i can't portward it. I have talked with the provider. They said I needed my own router and their router/fiberbox to be in brigdemode as it is now
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Nighthawk(R) X4S R7800 - Can't Open Port 1935
https://kb.netgear.com/30186/What-is-Double-NAT
https://kb.netgear.com/30187/How-to-fix-issues-with-Double-NAT
Couple of options,
1. Configure the modem for transparent bridge or modem only mode. Then use the NG router in router mode. You'll need to contact the ISP for help and information in regards to the modem being bridged correctly.
2. If you can't bridge the modem, disable ALL wifi radios on the modem, configure the modems DMZ/ExposedHost or IP Pass-Through for the IP address the NG router gets from the modem. https://kb.netgear.com/25891/DMZ-on-NETGEAR-routers
https://kb.netgear.com/24086/How-do-I-set-up-a-default-DMZ-server-on-my-Nighthawk-router
3. Or disable all wifi radios on the modem and connect the NG router to the modem, LAN to LAN configure AP mode on the NG router.
https://kb.netgear.com/24104/How-do-I-change-my-Nighthawk-router-to-AP-mode-after-I-ve-already-run-s...
Last time i talkede to them they said it was in brigdemode, I can't access the provides modem.
The NG router i have after the modem is in router mode
I will try to call them about the brigdemode
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Nighthawk(R) X4S R7800 - Can't Open Port 1935
One way to tell is look at the R7800s web page on the Advanced tab and Internet section. If you see a ##.##.###.### address for the WAN IP address, the modem is bridged. If you see something like 10, 192 or 172, then this is a private IP address and the modem isn't bridged.
When you set up PF or Triggering rules, be sure uPnP is disabled.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Nighthawk(R) X4S R7800 - Can't Open Port 1935
One way to tell is look at the R7800s web page on the Advanced tab and Internet section. If you see a ##.##.###.### address for the WAN IP address, the modem is bridged. If you see something like 10, 192 or 172, then this is a private IP address and the modem isn't bridged. - The IP there starts with 100
When you set up PF or Triggering rules, be sure uPnP is disabled. - Is It here i should turn it off? - https://gyazo.com/80424c958a058080d80a18521bc30b18
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Nighthawk(R) X4S R7800 - Can't Open Port 1935
Yes.
https://kb.netgear.com/23020/Opening-ports-for-internet-games-and-applications-on-NETGEAR-routers
Now I turned it off, but i still only can stream to the RTMP server via my localIP not my public
• What is the difference between WiFi 6 and WiFi 7?
• Yes! WiFi 7 is backwards compatible with other Wifi devices? Learn more