Orbi WiFi 7 RBE973
Reply

Nighthawk R8500 Amber Flashing Power Light after Firmware Update

Brighteyes
Initiate

Nighthawk R8500 Amber Flashing Power Light after Firmware Update

I updated the R8500's firmware utilizing the Router’s internet interface from version 1.0.2.136 to 1.0.2.144. After the update, the Router has a blinking amber light. 
 
Steps attempted to resolve amber light (per Netgear KB)
  • Restarted router
  • Attempted to reset - no effect at all after pressing reset button for >30 seconds.

Next, I attempted to upload the software to the router using TFTP as outlined here: https://kb.netgear.com/000059633/How-to-upload-firmware-to-a-NETGEAR-router-using-TFTP-client.

 
However, there has been no change in the router state. I tried both R8500-V1.0.2.136_1.0.99.chk and R8500-V1.0.2.144_1.0.99.chk.
 
Here is the log confirming successful transfer of the .chk file:
 
tftp> connect 192.168.1.1
tftp> status
Connected to 192.168.1.1.
tftp> put R8500-V1.0.2.136_1.0.99.chk
putting R8500-V1.0.2.136_1.0.99.chk to 192.168.1.1:R8500-V1.0.2.136_1.0.99.chk [netascii]
Sent 33029066 bytes in 152.1 seconds [1737229 bits/sec]
 
I'm out of ideas. Any suggestions on what I should try next?
 
 
Model: R8500|Nighthawk X8 Tri-Band AC5300 WiFi Router
Message 1 of 4

Accepted Solutions
antinode
Guru

Re: Nighthawk R8500 Amber Flashing Power Light after Firmware Update

> [...] After the update, the Router has a blinking amber light. [...]

 

   That'd be the Power indicator?  If so, then TFTP would be next step.

 

> I attempted to upload the software to the router using TFTP as
> outlined here: [...]

 

   That's not a very good guide for the command-line TFTP client program
on a Mac.

 

      https://community.netgear.com/t5/x/x/m-p/1766879

 

 

> [...] [netascii]

 

   That was the clue.

View solution in original post

Message 2 of 4

All Replies
antinode
Guru

Re: Nighthawk R8500 Amber Flashing Power Light after Firmware Update

> [...] After the update, the Router has a blinking amber light. [...]

 

   That'd be the Power indicator?  If so, then TFTP would be next step.

 

> I attempted to upload the software to the router using TFTP as
> outlined here: [...]

 

   That's not a very good guide for the command-line TFTP client program
on a Mac.

 

      https://community.netgear.com/t5/x/x/m-p/1766879

 

 

> [...] [netascii]

 

   That was the clue.

Message 2 of 4
Brighteyes
Initiate

Re: Nighthawk R8500 Amber Flashing Power Light after Firmware Update

Doh! Thanks for pointing that out. I got the router working now. Thank again!

Message 3 of 4
RNR1995
Tutor

Re: Nighthawk R8500 Amber Flashing Power Light after Firmware Update

Just an FYI

happenned here too with the 1.0.2.144 firmware

Ironically flashed one for someone remotely without issue, ours crashed and burned

The tftp recovery worked out fine though, just a bit of downtime

Model: R8500|Nighthawk X8 Tri-Band AC5300 WiFi Router
Message 4 of 4
Top Contributors
Discussion stats
  • 3 replies
  • 2188 views
  • 5 kudos
  • 3 in conversation
Announcements

Orbi WiFi 7