- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
Re: R7300DST cannot access router login after enable remote management
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I recently upgraded my router firmware and since then have not been able to access my router login. My internet and WiFi appear to be working fine, just can't access the router admin page. Before the firmware update, I was able to access the router login from my PC browser and the Genie mobile app just fine.
I tried everything found here, except for performing the factory reset which I would like to avoid if possible.
I tried from Edge, Chrome and IE browsers. I tried using www.routerlogin.net and my router's IP (192.168.0.1). I tried from a different PC, I tried over WiFi and direct LAN connection to the router. All give similar error: "192.168.0.1 refused to connect." I also tried from the mobile Genie app, but it's unable to locate my router though I'm connected to WiFi.
I tried rebooting my modem and my router and my PC, but same results.
Thanks.
Solved! Go to Solution.
Accepted Solutions
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I narrowed down the problem to the Remote Management setting. If I turn it on, after a day or so the router login stops working. It's strange because I recently started using this router after my old Asus died, though my daughter had previously used it at college for 2 years and I remotely accessed it just fine. Oh well, the Wi-Fi on this thing is starting to act flakey so maybe it's time for a new one anyways.
All Replies
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: R7300DST cannot access router login after recent firmware update
@dwtxbox wrote:
I tried from Edge, Chrome and IE browsers. I tried using www.routerlogin.net and my router's IP (192.168.0.1).
That's the usual address for modem/routers not for routers.
Try 192.168.1.1
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: R7300DST cannot access router login after fw update
Thanks for the reply. I actually changed my router's default IP from 192.168.1.1 to 192.168.0.1 back when I could still access the admin page. I confirmed on my PC the DHCP/Gateway address is 192.168.0.1 and the assigned IP address is 192.168.0.124. I tried it anyways but still got the error: "192.168.1.1 refused connection".
I gave up on doing anymore troubleshooting. I did a factory reset and I'm back in now.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: R7300DST cannot access router login after fw update
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: R7300DST cannot access router login after fw update
I'm having the same problem.
I reset back to the factory settings, reconfigured.
It worked for a week, now I'm back to the same issue.
When loging in from Genie, it gets router not found.
When loging in from 192.168.1.1, i get 192.168.1.1 refused to connect.
Any ideas?
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: R7300DST cannot access router login after fw update
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: R7300DST cannot access router login after fw update
It might help if you told people what the modem is in front of this router, if there is one. The model number could be useful. Is it, by any chance, also a router, with a set of LAN ports on the back?
The reason for asking is that a lot of people turn up here trying to put a router behind a modem that is also a router. That can complicate troubleshooting.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: R7300DST cannot access router login after fw update
For what it’s worth, my modem is a Motorola SB6141 and only has a WAN Port.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: R7300DST cannot access router login after fw update
My modem is an Arris SB6183 and I have no other routers on my network.
I reverted to the previous firmware (from V1.0.0.74_1.0.29 to V1.0.0.70_1.0.25) but that didn't help. Like a factory reset, it worked for a little bit, but eventually stopped after a day or so.
I just did another reset and this time I decided to not enable Remote Management or Dynamic DNS Service. It's been about a half day and it's still working, so we'll see.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I narrowed down the problem to the Remote Management setting. If I turn it on, after a day or so the router login stops working. It's strange because I recently started using this router after my old Asus died, though my daughter had previously used it at college for 2 years and I remotely accessed it just fine. Oh well, the Wi-Fi on this thing is starting to act flakey so maybe it's time for a new one anyways.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: R7300DST cannot access router login after enable remote management
I agree.
I had the same problem, and from this post or another reset, reconfigured, and did not turn on remote management.
It has been fine ever since
• What is the difference between WiFi 6 and WiFi 7?
• Yes! WiFi 7 is backwards compatible with other Wifi devices? Learn more