- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
RBS850 connection issues
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
RBS850 connection issues
The overall connection to and from seems great, the only problem I have is any device that's connected to the satellite seems to have terrible latency and packet loss issues.
The router and the satellite are no more than 20 ft apart in a single story 1800 ft² home with only one wall in between each other.
Is there any settings or anything I can tweak to make the satellite perform just like the router does? My son's Xbox is hardwired into the router and he has no issues, while mine is hardwired into the satellite and I have constant latency and every now and then packet loss.
The backhaul status is good, and the network map has green on both the router and the satellite. My ISP just swapped out the modem and router combo for just a straight-up modem, so I know there's not an issue with that interfering.
Thanks for the help!
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: RBS850 connection issues
What Firmware version is currently loaded?
What is the Mfr and model# of the Internet Service Providers modem/ONT the NG router is connected too?
What is the distance between the router and satellite(s)? 30 feet is recommended in between RBR and RBS to begin with depending upon building materials when wirelessly connected. https://kb.netgear.com/000036466/How-far-should-I-place-my-Orbi-satellite-from-my-Orbi-router
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: RBS850 connection issues
And the modem is a Calix Gigapoint 801Gv2
And right, I have it about the length that it recommends
Thanks
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: RBS850 connection issues
What channels are you using? Auto? Try setting manual channel 1, 6 or 11 on 2.4Ghz and any unused channel on 5Ghz.
Any Wifi Neighbors near by? If so, how many?
Try disabling the following and see:
Armor, IPv6 and Set 20/40Mhz Coexistence to 40Mhz only. Set Short preamble instead of Long preamble modes. Save settings and reboot the router and satellite(s).
You can try setting CTS from 64 to 2347 and see if this changes anything, if not, set it back to 64.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: RBS850 connection issues
And I have switched all of the settings that you listed and I'm still receiving the same issues, sadly.
Also, my Xbox and everything else has an open NAT but whenever I go into games especially call of duty It's still showing as moderate. How would I port forward these if I have UPNP enabled? I know using port forwarding while having UPNP enabled can cause issues.
I'm also using the ISP's DNS, would that cause issues?
Thanks!
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: RBS850 connection issues
If you have wifi neighbors near by, be sure your using different and far appart channels on the RBR.
Also try turning down the power output of the RBRs wifi radios from 100% to 50% and see if this changes anything. Under Advanced Tab/Advanced Settings/Wireless Settings
Until NG releases a fix for NAT filter, you may see moderate NAT in the game. Theres been some problems with NAT and NAT Filter on Orbi AX.
You can try using different DNS and see if this helps.
• What is the difference between WiFi 6 and WiFi 7?
• Yes! WiFi 7 is backwards compatible with other Wifi devices? Learn more