Good morning I always have disconnections, it starts with the satellite that disconnects but I placed it at 6m in open field. Then there is the router 2 or 3 times during the day sometimes the same fixed pink while it works. I made in addition the following adjustments: I have sonos at home on channel 1, so I'm on channel 5 in 2.4G, there are no nearby speakers so there is little noise. Cohabitation 20/40MHZ disabled cts/rts threshold at 2347 and short preamble mode for 2,4 and 5ghz networks as well. Another problem I have a subscription ISP 1Gbs down and 500 Mbs up, I check it on an apple tv connected in wifi via speedtest about 960 mbps downlink and 500 mbps uplink, but when I do the test in wifi with a wifi 6 device (iphone 11), I get painfully 330 mbps downlink while I have 500 mbps uplink, weird right? On the forum there is a lot of disconnection problem on this product, isn't it a firmware problem ? ( I downloaded the last one ) Can you help me
My apple tv and gigabit ethernet so no worries, otherwise I made measurements with wifi 5 and wifi 6 devices and it's the same result : 330Mbps instead of 900Mbps. But I insist my problem is the disconnections, I have just connected the satellite in ethernet and I have the impression that it works better. I saw on the forum that this model had problems in access point mode and blackhaul problems.
About the frequent disconnections, you might have a lot of electromagnetic interference due to other wireless devices... but if it's not so you might instead have a defective router or a defective satellite.
Try setting manual channel 1, 6 or 11 on 2.4Ghz and any unused channel on 5Ghz. Channel 5 should not be set as a manual channel. Any Wifi Neighbors near by? If so, how many?
Try disabling the following and see: IPv6 and Set 20/40Mhz Coexistence to 40Mhz only. Set Short preamble instead of Long preamble modes. Save settings and reboot the router and satellite(s).
Be sure that CTS and RTS values are changed to 2346 under Advanced Tab/Advanced Settings/Wireless Settings
Good morning I always have disconnections, it starts with the satellite that disconnects but I placed it at 6m in open field. Then there is the router 2 or 3 times during the day sometimes the same fixed pink while it works. I made in addition the following adjustments: I have sonos at home on channel 1, so I'm on channel 5 in 2.4G, there are no nearby speakers so there is little noise. Cohabitation 20/40MHZ disabled cts/rts threshold at 2347 and short preamble mode for 2,4 and 5ghz networks as well. Another problem I have a subscription ISP 1Gbs down and 500 Mbs up, I check it on an apple tv connected in wifi via speedtest about 960 mbps downlink and 500 mbps uplink, but when I do the test in wifi with a wifi 6 device (iphone 11), I get painfully 330 mbps downlink while I have 500 mbps uplink, weird right? On the forum there is a lot of disconnection problem on this product, isn't it a firmware problem ? ( I downloaded the last one ) Can you help me
The internet provider is bouygues telecom. I made your settings but it's not better. I specify that I'm in access point mode, so the settings are limited for example any unused channel on 5Ghz. The house is 150m2 and the 2 systems are 7m apart. There is no Wifi Neighbors near .
What is the building materials made of for the home? plaquatre
Can you move the RBS out farther? Try 30 feet? it's the same What channels are you using? 2 ghz --> 7 et 5 ghz 48 Any Wifi Neighbors near by? If so, how many? 1 more than 100m
firmware 3.2.11.2-1.2.13 which is not automatically downloadable.
so the satellite is jumping all the time I unplugged it and the router works alone but after a while it lights up in fixed pink
What is the building materials made of for the home? plaquatre
Can you move the RBS out farther? Try 30 feet? it's the same What channels are you using? 2 ghz --> 7 et 5 ghz 48< Try channel 1, 6 or 11. Don't use any of the other channels. 1, 6 and 11 are primary channels to use. Any Wifi Neighbors near by? If so, how many? 1 more than 100m
firmware 3.2.11.2-1.2.13 which is not automatically downloadable.
so the satellite is jumping all the time I unplugged it and the router works alone but after a while it lights up in fixed pink
You can downgrade the enstire system to v3.2.9.2 and see if anything changes.
Possible that you may have a bad RBS. I would open up a support ticket with NG and if nothing fails to stablize the RBS, ask about an RMA. @Blanca_O
My Setup | ISP SparkLight | Internet Cable 1000↓/50↑ CAX30 Gateway Mode | Wifi Router and RBK853 | Switches NG GS105/8, GS308v3, GS110MX and XS505M |
I tried with the new firmware 3.2.15.25 but still problems so I unplugged the system for 1 day. I plugged it back in yesterday and miracle it's been working for 12 hours, isn't that due to some information that remains in memory? To be continued ....
Well this switch does have green ethernet features:
"Conserves Energy The DGS-1008P 8-Port Gigabit Switch makes use of D-Link Green™ eco-friendly technology, providing energy savings, reduced power consumption, and a longer product life without sacrificing operational performance or functionality."
Can you connect the RBR directly to the main host router and see if you still seen problems with out the switch connected? I have my 853 system in AP mode connected directly to my main host router with out a switch. Not seeing any disconnections thus far.
My Setup | ISP SparkLight | Internet Cable 1000↓/50↑ CAX30 Gateway Mode | Wifi Router and RBK853 | Switches NG GS105/8, GS308v3, GS110MX and XS505M |
