This topic has been marked solved and closed to new posts due to inactivity. We hope you'll join the conversation by posting to an open topic or starting a new one.
Device Manager does not display all connected devices
Upgraded to 2.1.5.8 firmware today and I only have 5 devices shown as connected. WTH!?! I had almost 25 before and that means I can’t pause them. It was working great before and now I can’t shut off the boys wifi
Re: Device Manager does not display all connected devices
I downgraded to the 2.3.5.30 firmware and everything is good! All devices are showing up and connected to satellites. Don’t upgrade if you have an RBR50 AX3000 system!
Re: Device Manager does not display all connected devices
Do you mean that few devices now have internet connection but are not shown in the Attached Devices? Please try disabling Access Control under >> ADVANCED >> Security >> Access Control >> in the web GUI the click Apply. See then if you’ll see all devices now. If you see all devices then you can start using the access control again.
Re: Device Manager does not display all connected devices
No, there are a few wireless devices as well but not everything. Only a few. A total of only 8 devices are shown. Tried disabling from the GUI. No luck. Darn. Why did I upgrade to 2.1.5.8. Everything was working great.
Re: Device Manager does not display all connected devices
Please try a factory reset and setup from scratch with the RBR and RBS.
Be sure you update the Orbi app as well if thats what you are using...
@JamesAmazing wrote: Upgraded to 2.1.5.8 firmware today and I only have 5 devices shown as connected. WTH!?! I had almost 25 before and that means I can’t pause them. It was working great before and now I can’t shut off the boys wifi
Try enabling Beamforming and MIMO(MIMO may or maynot be needed) and WMM. Under Advanced Tab/Advanced Settings/Wireless Settings
Try disabling the following and see: Armor, Circle, Daisy Chain, Fast Roaming, IPv6 and Set 20/40Mhz Coexistence to 40Mhz only. Set Short preamble instead of Long preamble modes. Save settings and reboot the router and satellite(s).
Re: Device Manager does not display all connected devices
Wow. This is wonky. So I reset everything and did a fresh setup. The app says all is connected but everything is connected either to Orbi Router or RbS50 1. Nothing is connected to Satellite 2. From the web interface it says Satellite 2 is not connected ???
Re: Device Manager does not display all connected devices
Daisy chain is enabled. It’s so weird. I did a new setup a few times to get everything working for no devices show up under Satellite 2. I just figured it was acting weird but as I said, the web interface says it is not connected. App says it is (but again no devices connected) I can’t reboot everything right now kids are connected for school. There are 24 devices in the list now connected to either the router or Sat 1 but it isn’t really the same as before. I had iMac connected, etc. Devices are still missing. There was blue status on lights lit on both Sats
Re: Device Manager does not display all connected devices
When you get a chance, reboot the RBR only and leave the RBS on. See if any devcies connect to the RBS during the reboot since the RBRs wifi will not be available for a short time, this would force devices to the RBS...
Re: Device Manager does not display all connected devices
@JamesAmazing wrote: Worse now. App says both Sats connected but only 4 devices connected to the router. Web interface says no Sats connected. Bizarre.
Are you giving the network time to settle down? It looks to me that you're not waiting for the web GUI to be updated?
Re: Device Manager does not display all connected devices
The Web GUI or App is not updating correctly or displaying the correct devices etc. I am guessing it is all working (since everyone is connected) but I can't verify since I can't tell what devices are connected where. My iMac is connected but it does not show in the list? App says both SATs connected but Web GUI says only 1 is connected. Sigh.
Maybe time to upgrade the RBR50 and RBS. Too bad, it was working fine until this update and I don't want to try to downgrade the firmware.
Re: Device Manager does not display all connected devices
Access Control is disabled. Almost all of the devices in my house are not showing up in the list. It seems everytime I reboot different devices show up. It is wonky. I had 24 connected before, now it only displays 7 : S
Re: Device Manager does not display all connected devices
You might try this, power OFF all of your devices. Leaving one wired PC connected to the RBR. I would then setup a IP address reservation for the PC, save and apply. Then power on a device. Do the same thing. IP address reservation, save and apply. Try adding devices 1 at a time and set an IP address reservation.
Wondering if the IP address pool cache is getting hosed up thus the devices are not displaying correctly.
Re: Device Manager does not display all connected devices
Are you really sure the devices are attached to Orbi and not to another wifi? 🙂 Please check on the devices that the assigned IP addresses belong to the IP range of Orbi.
Re: Device Manager does not display all connected devices
I downgraded to the 2.3.5.30 firmware and everything is good! All devices are showing up and connected to satellites. Don’t upgrade if you have an RBR50 AX3000 system!
Re: Device Manager does not display all connected devices
i am seeing the same behavior, probably since the 2.8.1.5 fw. IE not all devices are listed, they only shown as connected to RBR. Satellite shown as Disconnected in Web UI but app and otherwise devices have connectivities. It feels like FW bugs, hope the next update will bring fixes. I am also getting sporatic latencies between devices in addition of the issues mentioned in this thread, which brought me to this forum.
Re: Device Manager does not display all connected devices
So I see a banner now says it's solved, with a link to solution. I followed link that went to a follow up post, which has a link that says solution is in the original post, that link doesn't go anywhere. I went thru entire thread and found an external link to some custom fw but not finding info on how to downgrade nor where to get older fw. Search result weren't useful... Is this really solved? thanks.
Re: Device Manager does not display all connected devices
You can rollback to a previous version by re-installing your previous version over the current version. All supported RBK50 firmware versions can be downloaded fromhere.
To (re)install firmware, head over to ADVANCED Firmware Update page and select the Manual Update. Then upload the firmware version you want to install. Repeate the same steps for all the Satellites. To access the Satellite UI, points your browser at its IP address.
