Re: New - Orbi RBR50 Router Firmware Version V2.7.2.104 Released

Aggie88 · ‎2021-02-14

Your answer makes me think about what I said. I am on Circle version 1 and that hasn't been affected for me. Sorry if I caused any confusion.

RJW84 · ‎2021-02-18

First post on here since looking to throw my RBR50/RBS50 setup in the bin...

Have just updated to V2.7.2.104 and now my system is dropping connection every 5 minutes and unuseable for work. I'm currently tethering off my phone.

The system was perfect up until this update.

Can I roll back to the previous software?

Cheers.

vajim · ‎2021-02-18

@RJW84 wrote:

Can I roll back to the previous software?

Cheers.

Yes

Go to the downloads section here (above) and enter model number.

Some have done it from the pc login page look for manual update.

Please let us know how it goes.

jvetro · ‎2021-02-18

Good day, does this firmware version resolve the issue with ethernet backhaul or is Firmware V2.5.1.16 still the latest to support this?

My Setup : Hitron ISP Router (Wifi Disabled) (1Gb/ 50Mb) > RBR50 (V2.5.1.16) > RBS50 (V2.5.1.16) (All connected through Ethernet Backhaul)

FURRYe38 · ‎2021-02-18

Only item you'll see is this with v104:

https://community.netgear.com/t5/Orbi/RBR50-Have-You-Installed-V2-7-2-104/m-p/2055265/highlight/true...

@jvetro wrote:
Good day, does this firmware version resolve the issue with ethernet backhaul or is Firmware V2.5.1.16 still the latest to support this?

My Setup : Hitron ISP Router (Wifi Disabled) (1Gb/ 50Mb) > RBR50 (V2.5.1.16) > RBS50 (V2.5.1.16) (All connected through Ethernet Backhaul)

vajim · ‎2021-02-19

@RJW84 wrote:
First post on here since looking to throw my RBR50/RBS50 setup in the bin...

Have just updated to V2.7.2.104 and now my system is dropping connection every 5 minutes and unuseable for work. I'm currently tethering off my phone.

The system was perfect up until this update.

Can I roll back to the previous software?

Cheers.

any progress?

RJW84 · ‎2021-02-19

I've done a clean install and still having a few niggles but definitely better than it was.

The RDS50 in the shed (10m away from RBR50) was having the most issues, and only picking up the 2.4ghz feed, but after lots of swearing at it and a couple of resets, seems to be holding a strong 5ghz connection now.

vajim · ‎2021-02-19

@RJW84 wrote:
I've done a clean install and still having a few niggles but definitely better than it was.

The RDS50 in the shed (10m away from RBR50) was having the most issues, and only picking up the 2.4ghz feed, but after lots of swearing at it and a couple of resets, seems to be holding a strong 5ghz connection now.

10m (32.8084 feet) is a bit beyond the recommended 30 feet or 9.144m

LuizAlmeida · ‎2021-02-22

Hi,

Just to let you know I did the upgrade from V2.6.1.40 to V2.7.2.104 version and had no issues.
First upgrade the satellites and then the RBR50.

Best Regards,

Luiz Almeida

vajim · ‎2021-02-22

@LuizAlmeida wrote:
Hi,

Just to let you know I did the upgrade from V2.6.1.40 to V2.7.2.104 version and had no issues.
First upgrade the satellites and then the RBR50.

Best Regards,

Luiz Almeida

keep an eye on it

FURRYe38 · ‎2021-02-22

Please add your experiences here as well:

https://community.netgear.com/t5/Orbi/RBR50-Have-You-Installed-V2-7-2-104/m-p/2055212

Thank you.

@LuizAlmeida wrote:
Hi,

Just to let you know I did the upgrade from V2.6.1.40 to V2.7.2.104 version and had no issues.
First upgrade the satellites and then the RBR50.

Best Regards,

Luiz Almeida

jvetro · ‎2021-02-22

So what I am reading is that .102 or .104 will fix the wired backhaul issue, but I may experience some ARP issues for the first 5 minutes. The issue I had before was the backhaul status was not showing as wired, I downgraded to 2.5.1.16 to have this work.

Can someone please confirm before I spend time this weekend in upgrading? Thank you in advance.

FURRYe38 · ‎2021-02-22

Yes, v102 and v104 work with ethernet back haul. Just this odd ARP storm is seen for about 2 minutes then stops, only if and when the RBS are ethernet connected to the RBR.

@jvetro wrote:
So what I am reading is that .102 or .104 will fix the wired backhaul issue, but I may experience some ARP issues for the first 5 minutes. The issue I had before was the backhaul status was not showing as wired, I downgraded to 2.5.1.16 to have this work.

Can someone please confirm before I spend time this weekend in upgrading? Thank you in advance.

vajim · ‎2021-02-23

Keep on eye on any update

ktula · ‎2021-02-23

Updated the router and the two satellites to this firmware last night and now anything that connects to one of the satellites is unable to connect to sites outside the home network.

Ha_Ku_Na · ‎2021-02-23

Power off the satellite for 1 min. Afterwards power on and check the state in the web admin GUI.

But be patient. This can take a few minutes.

ktula · ‎2021-02-23

I powered off the satellite but didn’t wait for a minute. I’ll try that later. While I was having the issue, the browser would only connect to orbilogin.com or routelogin.net but it was connecting to the satellite instead of the main router.

FURRYe38 · ‎2021-02-23

It's recommended to power OFF the ISP modem and entire Orbi system for 1 minute after a FW update, then back on with the modem first, then RBR, then RBS...

vajim · ‎2021-02-23

@ktula wrote:
I powered off the satellite but didn’t wait for a minute. I’ll try that later. While I was having the issue, the browser would only connect to orbilogin.com or routelogin.net but it was connecting to the satellite instead of the main router.

Maybe it's time to roll your firmware back and stop with the 1000 questions

ktula · ‎2021-02-23

@vajim wrote:
@ktula wrote:
I powered off the satellite but didn’t wait for a minute. I’ll try that later. While I was having the issue, the browser would only connect to orbilogin.com or routelogin.net but it was connecting to the satellite instead of the main router.
Maybe it's time to roll your firmware back and stop with the 1000 questions

Is the sole purpose of this Netgear Community for someone llike you to whine about users asking legitimate questions?

vajim · ‎2021-02-23

@ktula wrote:
@vajim wrote:
@ktula wrote:
I powered off the satellite but didn’t wait for a minute. I’ll try that later. While I was having the issue, the browser would only connect to orbilogin.com or routelogin.net but it was connecting to the satellite instead of the main router.
Maybe it's time to roll your firmware back and stop with the 1000 questions
Is the sole purpose of this Netgear Community for someone llike you to whine about users asking legitimate questions?

I missed the whine part

BoilerPlate · ‎2021-02-23

Vajim's lack of knowledge and experience, your mileage may vary. >vajim. User beware.

@ktula wrote:
Is the sole purpose of this Netgear Community for someone llike you to whine about users asking legitimate questions?

ktula · ‎2021-02-23

@FURRYe38 wrote:
It's recommended to power OFF the ISP modem and entire Orbi system for 1 minute after a FW update, then back on with the modem first, then RBR, then RBS...

The satellite most likely had a bad firmware upgrade. No amount of power cycling could resolve the issue. Eventually, i did a factory reset on the satellite. It didn't work after the first factory reset so i repeated it the second time (i put the reset button with a pin while the satellite is powered off for 7 seconds, and just to make sure, i also did that for 7 seconds while it's powered on). The second factory reset appeared to have worked.

FURRYe38 · ‎2021-02-23

Sometimes a reset is needed. I recommend 15 seconds press to reset.

Glad you got it working.

@ktula wrote:
@FURRYe38 wrote:
It's recommended to power OFF the ISP modem and entire Orbi system for 1 minute after a FW update, then back on with the modem first, then RBR, then RBS...
The satellite most likely had a bad firmware upgrade. No amount of power cycling could resolve the issue. Eventually, i did a factory reset on the satellite. It didn't work after the first factory reset so i repeated it the second time (i put the reset button with a pin while the satellite is powered off for 7 seconds, and just to make sure, i also did that for 7 seconds while it's powered on). The second factory reset appeared to have worked.

vajim · ‎2021-02-24

Keep an eye on it