- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
Re: No connection with internet at start to conninterne( needs 5+ seconds) once connected speed is
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I am having Orbi RB50 VS 2 system and generally it works perfect
My only issue is that if i start a connection to Internet, first i am getting warfning/message that there is no connection, then i have to wait several seconds and suddenly connection is available without any action from my side.
It is not a job killer but sometimes it irritates, and it has not always been this way.so i am trying to solve it.
I am using Windows 11 ( topic was allready there with Windows 10 ) and i alo have Norton 360 running
Message i see on my PC when i am using LAN connection, i am not sure fi iphone/ipad have same issue and i certainly get no messages overthere
Interned speed test tels me i am getting full speed i am paying for so once it is running there is no problem, its just when starting
Does anyone have suggestion what to do or don't
Thansk and regards
Chris
Solved! Go to Solution.
Accepted Solutions
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Most Ziggo boxes are modem/router combo devices and cause a doubt nat (but can't 100% confirm without an actual model)
A double nat happens when you cascade more than 1 router.
https://kb.netgear.com/30186/What-is-Double-NAT
Fixes? There’s 3 options but only use 1.
1. Put the modem/gateway in modem only/pass through mode. This disables its routing functions.
2. Leave the modem/gateway in router mode but put the Netgears IP address into its DMZ. This forwards the data to the netgear. You can either leave the modem/gateway’s wireless enabled or disabled. Just make sure its using a different wifi channel to prevent interference
3. Put the Netgear into access point mode. This disables its routing functions. Wifi/ethernet still works but it does disable some features.
https://kb.netgear.com/26765/Which-features-are-disabled-on-my-NETGEAR-router-when-it-is-set-to-AP-M...
All Replies
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: No connection with internet at start to conninterne( needs 5+ seconds) once connected speed is
1. what modem/gateway is it connected to?
2. what firmware is on the orbi router? And on the satellites?
3. You're only getting the notice on your windows pc's?
4. what happens if you disable norton?
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: No connection with internet at start to conninterne( needs 5+ seconds) once connected speed is
Good morning Plemans
Following to your answers
1. I am using Ziggo ISP, therefore the connectbox from Ziggo
2. Firmware on Orbi router 2.7.3.22
3. I am getting message on PC, not sure about Iphone and/or Ipad ( soory for not being more specicily)
4. I didnot try to disable norton so far
hope this helps
regards
Chris
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Most Ziggo boxes are modem/router combo devices and cause a doubt nat (but can't 100% confirm without an actual model)
A double nat happens when you cascade more than 1 router.
https://kb.netgear.com/30186/What-is-Double-NAT
Fixes? There’s 3 options but only use 1.
1. Put the modem/gateway in modem only/pass through mode. This disables its routing functions.
2. Leave the modem/gateway in router mode but put the Netgears IP address into its DMZ. This forwards the data to the netgear. You can either leave the modem/gateway’s wireless enabled or disabled. Just make sure its using a different wifi channel to prevent interference
3. Put the Netgear into access point mode. This disables its routing functions. Wifi/ethernet still works but it does disable some features.
https://kb.netgear.com/26765/Which-features-are-disabled-on-my-NETGEAR-router-when-it-is-set-to-AP-M...
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: No connection with internet at start to conninterne( needs 5+ seconds) once connected speed is
Hi Plemans
i checked with ISP, and they confirmed that I do have bridge mode setup on their router. What has happened they informed me that some time ago a firmware updated was done to modem. Modem has been reset by them, and I am now seeing if that will solve issue,
thanks for your support
regards
Chris
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: No connection with internet at start to conninterne( needs 5+ seconds) once connected speed is
I hope that fixes it for you!
If not, try putting the ziggo back in router mode (disable its wifi) and then put the netgears address into its dmz.
I've seen to many isp supplied devices not function properly in bridge/passthrough mode.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: No connection with internet at start to conninterne( needs 5+ seconds) once connected speed is
good morning
i wouild like to come back on our previous conversation.
I recently changed from ISP and ars eusing now Fritz Box to receibe internet signal.
Problem however remains, do you have any suggestions i copuld follow
thanks, Chris
• What is the difference between WiFi 6 and WiFi 7?
• Yes! WiFi 7 is backwards compatible with other Wifi devices? Learn more