NETGEAR is aware of a growing number of phone and online scams. To learn how to stay safe click here.
Forum Discussion
Solved
Orbi Limiting bandwidth wired and wireless
Hi all, I'm having a strange issue with my recently purchased RBR50 and I can't seem to run down what the culprit is. My ISP is Spectrum and I'm on their 400 down plan. I'm using the generic mod...
- For the curious (@furrye38), replacing the rbr50 and cable seems to have done the trick. Bear in mind that I did test 4 or 5 cat5e/cat6 cables prior to replacing the unit.
Ok, I can find out exactly what model number it is. I remember looking last night and not seeing anything I would easily identify as a model designation. I believe it's reporting a 192 IP address. What should I expect to see if there is a router in the modem?
Unfortunately, it looks like remote management isn't working currently so I can't definitively say what firmware I'm on, but it is current as of last nights factory resets.
I did not actively enable any QoS, Armor appears to activate automatically. Could that be negotiating my link speed down to 100?
My home is probably around 1600 sq ft. The satellite and router are probably 20 feet apart, separated by one interior wall.
2.4 is set to auto, if I recall correctly 5 was set to 36.
No neighbors within a couple hundred feet on any side.
As I mentioned, bemforming/mimo/daisy-chaining/fast roaming were are enabled/disabled as a part of my troubleshooting last night. I did not make any changes to the WMM settings.
The part that's confusing to me is that the modem will give me a full 500 down when connected directly to my computer, but the second I plug it in, every link drops to 100 down.
badbet wrote:Ok, I can find out exactly what model number it is. I remember looking last night and not seeing anything I would easily identify as a model designation. I believe it's reporting a 192 IP address. What should I expect to see if there is a router in the modem?
If the RBR is getting a 192.168 or maybe a 10.something IP address on the WAN port, if so, then there is a router at the modem. If the WAN reports a ##.##.###.### IP address, then there probably isn't a router at the modem.
Unfortunately, it looks like remote management isn't working currently so I can't definitively say what firmware I'm on, but it is current as of last nights factory resets.
I did not actively enable any QoS, Armor appears to activate automatically. Could that be negotiating my link speed down to 100?
If doing a factory reset and setup from scratch, Armor will ask you if you want it enabled or not. I would NOT enabled it. Others have mentioned this feature seems to cause some problems...
My home is probably around 1600 sq ft. The satellite and router are probably 20 feet apart, separated by one interior wall.
20 feet is too close. 30 feet is recommended in between them to begin with depending upon building materials when wirelessly connected.
2.4 is set to auto, if I recall correctly 5 was set to 36.
No neighbors within a couple hundred feet on any side.
As I mentioned, bemforming/mimo/daisy-chaining/fast roaming were are enabled/disabled as a part of my troubleshooting last night. I did not make any changes to the WMM settings.
Keep Beamforming enabled. Daisy Chain is only needed if you have more then 1 satellite connected and placed in a linear line out from the router thus piggy backing of one another.
The part that's confusing to me is that the modem will give me a full 500 down when connected directly to my computer, but the second I plug it in, every link drops to 100 down. Need to find out the model and if this modem has a built in router or not.
Thanks for getting back to me.
Ok, so I'm confused. In the case of either a 192. or 10. address it would indicate the presence of a router within the modem?
I was able to track down the modem model number as well: Hitron E31N2V1
I wasn't prompted, but I'll disable it when I get home. Additionally, I'll see what I can do about repositioning the satellite. That said, I don't see how that would impact the link speed on the router. Regardless, it's a problem that needs fixing.
Thanks again.
badbet wrote:Thanks for getting back to me.
Ok, so I'm confused. In the case of either a 192. or 10. address it would indicate the presence of a router within the modem? YES.
I was able to track down the modem model number as well: Hitron E31N2V1
I believe this is a model only with not router built in. Should be ok...
I wasn't prompted, but I'll disable it when I get home. Additionally, I'll see what I can do about repositioning the satellite. That said, I don't see how that would impact the link speed on the router. Regardless, it's a problem that needs fixing.
Try the speed test with out the RBS online. Turn it off. Hoping a reset and setup from scratch, don't enable Armor should have better results.
I'll give it a shot, thanks.
I'm going to test with a CAT6 cable as well.