Orbi RBR50 Router Firmware Version V2.7.2.102

What version of FW is on the RBS Currently? 

---

aaronka wrote:

I'm not noticing any performance issues but my admin web page for the router shows my RBS50 satellite as "disconnected", which I know it isn't.  In my iOS Orbi app it shows it connected and functioning.  Also on the Firmware Update page of the web interface it keeps trying to update the RBS50 but fails.

---

Speed test results with v102 loaded on a RBK50 System in AP mode. RBS ethernet connected behind two LAN switches.

Wired to RBR:

Iphone 12 Max connected to RBS:

Where/how did you get the ver 2.7.2.102?

Are these results different than with previous versions?

Manually applied V2.7.1.60 then found v102 available to update to on the RBR and RBS. 

About the same. I'll be trying router mode as well. 

---

alokeprasad wrote:

Where/how did you get the ver 2.7.2.102?

 

Are these results different than with previous versions?

---

RBS50 is running V2.7.1.60 same as what the RBR50 was on before the forced firmware update to V2.7.2.10

FURRYe38 wrote:

What version of FW is on the RBS Currently? 

---

aaronka wrote:

I'm not noticing any performance issues but my admin web page for the router shows my RBS50 satellite as "disconnected", which I know it isn't.  In my iOS Orbi app it shows it connected and functioning.  Also on the Firmware Update page of the web interface it keeps trying to update the RBS50 but fails.

---

 

---

I found that v102 was offered for both RBR and RBS on the RBRs FW upate check web page. How I updated mine. Update All. 

RBK50 online in router mode with v102 loaded behind a CM1200 cable modem:

RBS50 ethernet connected behind 3 NG GS series non managed switches. Small ARP storm seen when RBS was syncing then it stopped. Network is stable and working. 

For users with a 50 series and a RBS20, be sure to upate the RBS20s FW. Mine connected via ethernet but the radios were disabled, so I updated the RBS FW since it was a few behind. Up and running now:

:smileysad:

Wired. 

Ever since NG released v4 and follow on versions, these ARP storms are now present after any RBS are connected via ethernet behind a switch to the RBR. Something not seen on v16. Though up to before v102, the ARP storm didn't seem to stop, now after about a minute or two, the storm stops and the network settles in and right now, still working just fine with the two RBS ethernet conneted. 

---

GMoGoody8 wrote:
Wired or Wireless Backhaul when you saw the ARP storm.

---

I seem to be having significant issues post firmware update.  I got a notification that security updates were available, so I installed them thinking it would be fine.  Now my RBR50 shows up as offline and my internet connection for wireless is dropping regularly.  This impacts my cellphone, chromecasts, smart lightbulbs, and security cameras.  I have rebooted the router a few times, rebooted/reset the modem, etc.  I'm not sure what is causing the issue but it is really frustrating.  Right now the app shows internet is offline but I'm writing this post on my laptop via wifi.  This is very strange. I have also been getting some credential issue notifications while using wifi on my devices.  

What issues were you seeing before the reset? Glad the reset worked as it's a normal troubleshooting step to try when problems are seen. 

Thanks for letting us know, 

---

jdy0204 wrote:
After having quite a few issues I did a factory reset and now I'm not having any issues with the new firmware.

---

Ok, Thanks for letting us know the reset worked. 

Enjoy. :smileywink:

---

jdy0204 wrote:
See my earlier comment. It was having intermittent issues with internet connectivity and the satellite and the router were alternating disconnecting. Wired connections were fine.

---