- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
About printer through ORBI
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi guys,
I recently extended my wi-fi with ORBI. Let’s call the original wi-fi WIFI1. ORBI is connected to the WIFI1 modem via ethernet with its IP (192.168.1.100) and generates a new wi-fi signal: let’s call it WIFI2. ORBI has a different class of IP’s (10.0.0.x). I have a printer connected via WPS to WIFI1 with its IP address 192.168.1.108. It only works if a device is connected to WIFI1.
Is there any way to use it connecting a device to WIFI2 and routing the connection to the printer in some way?
Thanks a lot
Pale77
Solved! Go to Solution.
Accepted Solutions
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Thanks a lot, it now works fine.
I only had followed the setup instructions and it had set as two routers one after the other.
Now it is in AP mode and the only one anomaly is that I connected to the ORBI router an audio device via ethernet and it isn't shown within the connected devices. Strangely it is shown with 192.168.1.106 IP in the modem/router, but anyway it works fine.
But in AP mode it seems impossible to remotely access the ORBI (te selectioni s shown in grey and cannot be activated): is that right?
Thanks again
Pale77
All Replies
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: About printer through ORBI
What device(s) are attempting to use the printer from the Orbi Wi-Fi? (i.e. desktops, laptops, PC, Apple, tablets? etc.)
I think the problem will "go away" if the Orbi is set into Access Point (AP) mode. On the Advanced tab, select Advanced Setup, select Router/AP Mode. In general, it is not a good practice to stack one router behind another. When every device is getting an IP address directly from the first WiFi router, devices should "find" the printer with no problem.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Thanks a lot, it now works fine.
I only had followed the setup instructions and it had set as two routers one after the other.
Now it is in AP mode and the only one anomaly is that I connected to the ORBI router an audio device via ethernet and it isn't shown within the connected devices. Strangely it is shown with 192.168.1.106 IP in the modem/router, but anyway it works fine.
But in AP mode it seems impossible to remotely access the ORBI (te selectioni s shown in grey and cannot be activated): is that right?
Thanks again
Pale77
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: About printer through ORBI
When in AP mode, some features like remote access are no longer enabled.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: About printer through ORBI
But what about the device connected to the ethernet port which is invisible to the Orbi?
Pale77
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: About printer through ORBI
@77PALE77 wrote:
Thanks for the answer, now it’s clear.
But what about the device connected to the ethernet port which is invisible to the Orbi?
I have several devices that do not show up constantly on the "Attached Devices" display. (Nest thermostat is one.) What I have discovered is that when they are "doing something", they pop up on the display. But, when they go quiet again, they disappear. When the audio streaming device is invisible, is it actually "on" and streaming? My test for the Nest was actually sort of fun. I would open Attached Devices, verify that the Nest was not there, and then open the Nest app on my phone. Wow, there it is! As long as the Nest app was open, the thermostat remained on the display. Shut down the app and within a few minutes, Nest disappears. Did it several times until the wife said, "what the heck are you doing?"
Or, it could be something else. I am frequently incorrect.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: About printer through ORBI
Since having two routers working in router mode is generally bad, and double-NAT can cause problems, you're best off either leaving the Orbi in AP mode and using the modem/router as your router, or, alternatively, putting the modem in bridge mode (terminology varies by model), so that it's only a modem for practical purposes, and then using the Orbi in router mode. Which way you do it depends on which one has better features, etc. If, for example, remote management is important to you, and the modem doesn't offer that, then I'd put the modem in bridge mode and use the Orbi in router mode.
• What is the difference between WiFi 6 and WiFi 7?
• Yes! WiFi 7 is backwards compatible with other Wifi devices? Learn more