- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
CM1100 and Orbi RBR50 - recommended settings
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello,
I have an existing currently working almost flawlessly (on AP mode) with an att uverse gateway. A very straightforward setup.
I will be moving to xfinity internet soon and already purchased CM1100 (from Costco). I plan to connect the same Orbi RBR50 (+1 RBS50) to the CM1100 (cable modem).
I believe I would need to switch the RBR50 settings back to Router mode before I move to connections from the att gateway to the CM1100, correct? Will there be any problem if, for some reason, the RBR50 was left on AP mode when moved to the CM1100?
I would also like to seek for recommend settings (if any) on either the CM1100 or RBR50. At the start, I plan to keep the connections/setup simple then experiment on some advanced settings later on.
Thanks
Solved! Go to Solution.
Accepted Solutions
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
A power OFF of the modem for 1 minute then back ON maybe needed to effect this.
All Replies
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: CM1100 and Orbi RBR50 - recommended settings
Yes the RBR needs to revert back to router mode if you connect it to the CM1100.
Disable LAG on the CM modem and be sure to connecdt to WAN #1 port on the CM modem with the RBR.
Be sure to power OFF the RBR after setting router mode. THen connect to the CM modem. Power the modem ON first and besure it's activated by the ISP correctly. After the modem is online fully, then power ON the RBR. It should get internet services with out any other changes.
This would be all thats needed.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: CM1100 and Orbi RBR50 - recommended settings
Thanks for the information. I have noted the LAG setting on the CM.
I wanted to make sure that aside from changing the RBR settings from AP to Router mode, no other changes are needed.
Also, I just remembered that I need to ask the tech about the CM FW update. I assume that the CM only have the 'default' FW version loaded (V2.01.02) out-of-the-box. I wonder if the comcast-deployed FW (V6.01.07) is automatically uploaded during activation.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: CM1100 and Orbi RBR50 - recommended settings
ISPs are reqponsible for FW updates on cable modems. There is no user appliable FW updates for modems. Some ISP may not push FW udpates to user owned modem. Contact the ISP for further information regarding this.
Good Luck.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
A power OFF of the modem for 1 minute then back ON maybe needed to effect this.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: CM1100 and Orbi RBR50 - recommended settings
Update: Xfinity service activation went on smoothly, We run into a small issue when the technician immediately moved the RBR connection from the att gateway to the CM once he determined that CM was working. I had perform a few reboots to get all the equipment sync'ed up and change the RBR setting from AP to Router mode.
Confirmed that the latest Comcast-deployed FW was installed; and, the LAG is disabled
Thanks you for all your input. much appreciated.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
• What is the difference between WiFi 6 and WiFi 7?
• Yes! WiFi 7 is backwards compatible with other Wifi devices? Learn more