Reply

Re: Connected Devices displaying differently since update to V1.3.0.12

Namdnas
Tutor

Connected Devices displaying differently since update to V1.3.0.12

Before I updated to the new V1.3.0.12 firmware, under "Attached Devices", it would show which devices were connected to the router and which were connected to the satellite.  Now, after the update to V1.3.0.12, it only shows the Satellite at the top, along with it's IP and MAC address (under "Connected Satellites).  Then below (under "Connected Devices), it has a list of every device connected to the home network (14 total for me), IP/MAC addresses of each and if it's a wired/wireless connection.  It no longer sorts the devices as being connected to the Router or to the Satellite.  Before, this was really handy, expecially to diagnose connection issues with whatever device.  Is this normal, a bug, or what?  If this is a bug or intentional, can we get that re-implemented in a future update?

 

Thanks!

Model: Orbi High-Performance AC3000 Tri-Band WiFi System (RBK50)
Message 1 of 11

Accepted Solutions
rhester72
Virtuoso

Re: Connected Devices displaying differently since update to V1.3.0.12

Something you can try until it's fixed upstream (advanced users only!):

 

- Go to the debug page and enable telnet

- Telnet into the router

- Execute the following:

 

nvram set enable_adv_attached=1
nvram commit

- Exit telnet

- Go to the debug page and disable telnet (please don't forget this step!)

 

Rodney

View solution in original post

Message 8 of 11

All Replies

Re: Connected Devices displaying differently since update to V1.3.0.12

hi

 

go to

 

orbilogin.com/debug.htm

 

tick

 

Enable advanced view of Attached Devices page

 

and click save down the botton of the page

 

close the window and go back to the attached devices list and you will see the better attached devices list

 

pete

Message 2 of 11
krf007
Star

Re: Connected Devices displaying differently since update to V1.3.0.12

Thank you.  I like being able to see which unit my devices are connected to and used your fix.  The fix also shows whether it is 2.4 or 5 which is also nice to know.

Model: Orbi High-Performance AC3000 Tri-Band WiFi System (RBK50)
Message 3 of 11
XBond
Apprentice

Re: Connected Devices displaying differently since update to V1.3.0.12

This is now happening again with firmware v1.3.0.26.

 

Can no longer see whether or not a device is attached to the router or satellite on the 'Attached Devices' page, and I do not see a 'Enable advanced view...' on the debug page.

 

This was super useful.

Message 4 of 11

Re: Connected Devices displaying differently since update to V1.3.0.12

you can see whats attached to the sats by accessing there web pages from their ip addresses , however you cant tell if they are connected to 2.4 or 5 gig at this stage

Message 5 of 11
XBond
Apprentice

Re: Connected Devices displaying differently since update to V1.3.0.12

Okay, but not nearly as convenient as before. Little baffling that a super useful feature was removed. 😄
Message 6 of 11

Re: Connected Devices displaying differently since update to V1.3.0.12


@XBond wrote:
. Little baffling that a super useful feature was removed. 😄

 

certainly not disagreeing with you there Smiley Frustrated

Message 7 of 11
rhester72
Virtuoso

Re: Connected Devices displaying differently since update to V1.3.0.12

Something you can try until it's fixed upstream (advanced users only!):

 

- Go to the debug page and enable telnet

- Telnet into the router

- Execute the following:

 

nvram set enable_adv_attached=1
nvram commit

- Exit telnet

- Go to the debug page and disable telnet (please don't forget this step!)

 

Rodney

View solution in original post

Message 8 of 11
Rustproofcorn
Luminary

Re: Connected Devices displaying differently since update to V1.3.0.12

Worked perfect Rodney thank u
Message 9 of 11
CDELL801
Aspirant

Re: Connected Devices displaying differently since update to V1.3.0.12

also worked for me on 1.4.0.34

Message 10 of 11
Hydro130
Luminary

Re: Connected Devices displaying differently since update to V1.3.0.12

Thank you for the telnet instructions, Rodney

 

That worked like a champ for me after a recent factory reset - your assistance is much appreciated!

 

Cheers, Chris

Message 11 of 11
Top Contributors
Discussion stats
  • 10 replies
  • 30360 views
  • 7 kudos
  • 8 in conversation
Announcements