- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
Re: Issues with Orbi AC3000 losing internet connectivity with ATT Uverse(NVG589)
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Issues with Orbi AC3000 losing internet connectivity with ATT Uverse(NVG589)
I have ATT uverse and am trying to run my Orbi AC3000 in router mode behind it and I periodically, at least 2-3 a day lose connectivity to the internet. The Orbi management page shows no errors in internet connectivity and all devices both wired and wireless have connectivity to the Orbi. However, I can't get any connectivity to the internet, as an example if I try to ping anything it times out. I have found in this situation if I go to the Orbi managment page and just run a Test connectivity from the internet tab once it gets about halfway through my internet connectivity comes back up. Otherwise I have to wait several minutes for this to resolve itself. I have updated to the latest Firmware on the Orbi. And yes I know I can put it in AP Mode, but then I lose some of the router functions I bought the Orbi for, specifcally Circle.
Lastly as far as I can tell the NVG589 is setup correctly. When I first set the Orbi up as a router I had issues with double NAT'ing, but was able to solve that by changing the settings on the Uverse box. I had a previous Linksys router so I just needed to update the Uverse box with the Orbi MAC address, directions here http://www.dslreports.com/faq/17734. Everything after that cleared up, except for this loss of connectivty, anyone else experience this and solve it?
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Issues with Orbi AC3000 losing internet connectivity with ATT Uverse(NVG589)
A tested workaround that I currently have and has solved this issue for me to to reduce the lease renewal time in Orbi as follows:
* From browser go to the router's debug page (http://192.168.1.1/debug.htm). Use your router's IP address or http://orbilogin.com/debug.htm
* Enter admin as user name and your router’s management password
* Tick "Enable Telnet" option
* Use Telnet from a computer attached to Orbi to connect to your Router telnet 192.168.1.1 and enter admin and the same password as above
* Enter the following commands:
* root@RBR50:/# config get wan_lease — Should give you --> 86400
* root@RBR50:/# config set wan_lease=720
* root@RBR50:/# config commit
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Issues with Orbi AC3000 losing internet connectivity with ATT Uverse(NVG589)
Modem Combo Units:
This would be a double NAT condition which isn't recommended. https://kb.netgear.com/30186/What-is-Double-NAT
Couple of options,
1. Configure the modem for transparent bridge or modem only mode. Then use the Orbi router in router mode. You'll need to contact the ISP for help and information in regards to the modem being bridged correctly.
2. If you can't bridge the modem, disable ALL wifi radios on the modem, configure the modems DMZ/ExposedHost or IP Pass-Through for the IP address the Orbi router gets from the modem. Then you can use the Orbi router in Router mode.
I would try Option #2...
@RBK50_user1 wrote:I have ATT uverse and am trying to run my Orbi AC3000 in router mode behind it and I periodically, at least 2-3 a day lose connectivity to the internet. The Orbi management page shows no errors in internet connectivity and all devices both wired and wireless have connectivity to the Orbi. However, I can't get any connectivity to the internet, as an example if I try to ping anything it times out. I have found in this situation if I go to the Orbi managment page and just run a Test connectivity from the internet tab once it gets about halfway through my internet connectivity comes back up. Otherwise I have to wait several minutes for this to resolve itself. I have updated to the latest Firmware on the Orbi. And yes I know I can put it in AP Mode, but then I lose some of the router functions I bought the Orbi for, specifcally Circle.
Lastly as far as I can tell the NVG589 is setup correctly. When I first set the Orbi up as a router I had issues with double NAT'ing, but was able to solve that by changing the settings on the Uverse box. I had a previous Linksys router so I just needed to update the Uverse box with the Orbi MAC address, directions here http://www.dslreports.com/faq/17734. Everything after that cleared up, except for this loss of connectivty, anyone else experience this and solve it?
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Issues with Orbi AC3000 losing internet connectivity with ATT Uverse(NVG589)
• What is the difference between WiFi 6 and WiFi 7?
• Yes! WiFi 7 is backwards compatible with other Wifi devices? Learn more