- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
Re: Need help with Teardown/Putting Orbi back together
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Need help with Teardown/Putting Orbi back together
It seems this can only be fixed by taking apart the casing and outing it back together, but I can’t find any teardown tutorials.
Short of taking this to a Netgear center (we don’t have first party ones here in India as far as I know), can anyone help me with potential instructions? Or do i need to take it to a professional?
Any help would be appreciated.
Thanks
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Need help with Teardown/Putting Orbi back together
There maybe some screws under the RBS rubber feet that need to come out to help. Try taking thes screws out if you can.
Find a pro person near by if you can to help.
Hope the RBS isn't damaged and non functional. Looks like it took a big fall.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Need help with Teardown/Putting Orbi back together
The satellite itself is functional. I have wrapped it up a bit in cling-film to avoid getting dust and other stuff inside.
Will try and reach out to a service center locally.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Need help with Teardown/Putting Orbi back together
Hope they can help. Let us know how it goes.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Need help with Teardown/Putting Orbi back together
Turns out the screws are under the plastic covering the back where the network ports and power button are.
Remove that plastic piece with sync/power/reset text and remove the two screws.
The case is split in two pieces front and back...so you also have to remove the feet in the center of the botton and either remove the bottom netgear sticker or slit it along the seam.
The peices come apart pretty easily at that point. There are internal clips so you have to slide the front or back up/down against the other slightly.
Good luck.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Need help with Teardown/Putting Orbi back together
Would you mind posting some photos when you have it open? I have something that isn't secured correctly in my router, it rattles when I shake it. I am assuming it is an antenna, but I'd like to see what it looks like before I attempt to take it apart.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Need help with Teardown/Putting Orbi back together
Great, thanks a lot for this. I have been running the device with a tight Cellophane (Sara?) wrap to ensure no dust goes in, while keeping it at a place with sufficient ventilation.
I'll try this out over the weekend and get back with how it goes.
Btw, in case you know, are there any cables/ribbons I need to be careful with while splitting open the device?
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Need help with Teardown/Putting Orbi back together
The MB and everything attached to it is screwed to one side of the clamshell. So no cables etc to worry about.
I should have mentioned though that the screws are a T-10 torx screw. And the hole to get to them is long and thin so a lot of bit sets won't work. Kind of a pain. The screws attaching the MB to the shell internally are the same as well.
An example of one that would.
• What is the difference between WiFi 6 and WiFi 7?
• Yes! WiFi 7 is backwards compatible with other Wifi devices? Learn more