Re: Streaming issues on Xbox One X

James_Wheelz · ‎2019-12-13

So I'm confused as to which model I have so that's why I posted the image of the one I have and I got an additional satellite for this system. But for some reason on my xbox one x. Streaming gives poor quality and I keep being disconnected from Call of Duty modern warfare 2019 servers. What should I do? I have beamforming on, UPnP is on, Ipv6 is on, mu mimo is on, daisy chain is on, and 20/40 mhz coexistence is on. Why is this happening? It's on firmware version is 2.5.0.38. Please help

James_Wheelz · ‎2019-12-13

I also Unplugged the xbox one x and left it Unplugged for 30 minutes. I have also Unplugged the orbi system. And still no difference. And I have Cox Gigablast and have the Cox Panoramic gateway which I put on bridge mode so I don't get double nat.

FURRYe38 · ‎2019-12-15

What is the Mfr and model# of the ISP modem the NG router is connected too?

What is the size of your home? Sq Ft?
What is the distance between the router and satellite(s)? 30 feet is recommended in between RBR and RBS to begin with depending upon building materials when wirelessly connected. https://kb.netgear.com/000036466/How-far-should-I-place-my-Orbi-satellite-from-my-Orbi-router

What channels are you using? Auto? Try setting manual channel 1, 6 or 11 on 2.4Ghz and any unused channel on 5Ghz.
Any Wifi Neighbors near by? If so, how many?

Try enabling Beamforming and MIMO(MIMO may or maynot be needed) and WMM. Under Advanced Tab/Advanced Settings/Wireless Settings

Try disabling the following and see:
Armor, Circle, Daisy Chain, Fast Roaming, IPv6 and Set 20/40Mhz Coexistence to 40Mhz only. Save settings and reboot the router and satellite(s).

@James_Wheelz wrote:
So I'm confused as to which model I have so that's why I posted the image of the one I have and I got an additional satellite for this system. But for some reason on my xbox one x. Streaming gives poor quality and I keep being disconnected from Call of Duty modern warfare 2019 servers. What should I do? I have beamforming on, UPnP is on, Ipv6 is on, mu mimo is on, daisy chain is on, and 20/40 mhz coexistence is on. Why is this happening? It's on firmware version is 2.5.0.38. Please help

James_Wheelz · ‎2019-12-16

CGM4140COM first 0 is a zero and second 0 is a Oh. It's the Cox Panoramic Gateway. My house is about 6000 square feet. The satellites are about 30 feet apart. And my xbox is about 20 feet away from the satellite. So hardwiring isn't possible for me.

James_Wheelz · ‎2019-12-16

Also I'm in a house between 2 neighbors. Neighbor to the left of my house is about 15 feet away. Neighbor to the right is about 40 feet away. And when pulling up wifi one of their internet does show up when selecting which network to use.

FURRYe38 · ‎2019-12-16

If your ISP modem is a gateway, it probably already had built in wifi and a router.

This would be a double NAT condition which isn't recommended. https://kb.netgear.com/30186/What-is-Double-NAT
https://kb.netgear.com/30187/How-to-fix-issues-with-Double-NAT
Couple of options,
1. Configure the modem for transparent bridge or modem only mode. Then use the Orbi router in router mode. You'll need to contact the ISP for help and information in regards to the modem being bridged correctly.
2. If you can't bridge the modem, disable ALL wifi radios on the modem, configure the modems DMZ/ExposedHost or IP Pass-Through for the IP address the Orbi router gets from the modem. Then you can use the Orbi router in Router mode.
3. Or disable all wifi radios on the modem and connect the Orbi router to the modem, configure AP mode on the Orbi router. https://kb.netgear.com/31218/How-do-I-configure-my-Orbi-router-to-act-as-an-access-point and https://www.youtube.com/watch?v=H7LOcJ8GdDo&app=desktop

I would try option #2 first...