The speed of the internet does not reach full speed for the whole house. The last distributor gives

[azooz5005]

The speed of the internet does not reach full speed for the whole house. The last distributor gives

Whta is the best settings ?

i do some change before but i dont know what is it exaxtly

before 5 days i have full speed every where but when i restore to defult and i change some settings the problem occurred

My settings is in attach link

https://ibb.co/PM8pgJR
https://ibb.co/zsfMQD2
https://ibb.co/T4PWStj
https://ibb.co/GMVTgfB
https://ibb.co/tMfyD3s

[FURRYe38]

What Firmware version is currently loaded?
What is the Mfr and model# of the ISP modem/ONT the NG router is connected too?

What is the size of your home? Sq Ft?
What is the distance between the router and satellite(s)? 30 feet is recommended in between RBR and RBS to begin with depending upon building materials when wirelessly connected. https://kb.netgear.com/000036466/How-far-should-I-place-my-Orbi-satellite-from-my-Orbi-router

What channels are you using? Auto? Try setting manual channel 1, 6 or 11 on 2.4Ghz and any unused channel on 5Ghz.
Any Wifi Neighbors near by? If so, how many?

Try enabling Beamforming and MIMO(MIMO may or maynot be needed) and WMM. Under Advanced Tab/Advanced Settings/Wireless Settings

Try disabling the following and see:
Armor, Circle, Daisy Chain, Fast Roaming, IPv6 and Set 20/40Mhz Coexistence to 40Mhz only. Set Short preamble instead of Long preamble modes. Save settings and reboot the router and satellite(s).

[azooz5005]

What Firmware version is currently loaded?
What is the Mfr and model# of the ISP modem/ONT the NG router is connected too?

Orbi50RBK
Router Firmware Version

What is the size of your home? Sq Ft?
What is the distance between the router and satellite(s)? 30 feet is recommended in between RBR and RBS to begin with depending upon building materials when wirelessly connected. https://kb.netgear.com/000036466/How-far-should-I-place-my-Orbi-satellite-from-my-Orbi-router

all signal is blue

The house is completely covered
But the speed does not reach full speed
As the network is 5G, but everywhere in the house does not reach full speed and previously it was complete

What channels are you using? Auto? Try setting manual channel 1, 6 or 11 on 2.4Ghz and any unused channel on 5Ghz.
Any Wifi Neighbors near by? If so, how many?

2.4G chanel ( Auto )

5G ( 48 )

Try enabling Beamforming and MIMO(MIMO may or maynot be needed) and WMM. Under Advanced Tab/Advanced Settings/Wireless Settings

All enable

Try disabling the following and see:
Armor, Circle, Daisy Chain, Fast Roaming, IPv6 and Set 20/40Mhz Coexistence to 40Mhz only. Set Short preamble instead of Long preamble modes. Save settings and reboot the router and satellite(s).

Fast Roaming is enable

[Retired_Member]

did i just see doubles?

[azooz5005]

i dont understand ( did i just see doubles? )

my main modem is HG8245W5 and the Orbi for wifi only i put the cable in internet port "Yellow" ( not in ethernet )

---

@Retired_Member wrote:

did i just see doubles?

---

[Retired_Member]

---

@azooz5005 wrote:

i dont understand ( did i just see doubles? )

my main modem is HG8245W5 and the Orbi for wifi only i put the cable in internet port "Yellow" ( not in ethernet )

---

@Retired_Member wrote:

did i just see doubles?

---

---

Message 3 of 5 is hard to determine who's on first.....are you adding more info or answering the dozens of questions already asked?

also...does your modem have wifi built in?

[azooz5005]

---

@Retired_Member wrote:

---

@azooz5005 wrote:

i dont understand ( did i just see doubles? )

my main modem is HG8245W5 and the Orbi for wifi only i put the cable in internet port "Yellow" ( not in ethernet )

---

@Retired_Member wrote:

did i just see doubles?

---

---

Message 3 of 5 is hard to determine who's on first.....are you adding more info or answering the dozens of questions already asked?

also...does your modem have wifi built in?

---

adding more info + answering the dozens of questions a

[Retired_Member]

---

@azooz5005 wrote:

---

@Retired_Member wrote:

---

@azooz5005 wrote:

i dont understand ( did i just see doubles? )

my main modem is HG8245W5 and the Orbi for wifi only i put the cable in internet port "Yellow" ( not in ethernet )

---

@Retired_Member wrote:

did i just see doubles?

---

---

Message 3 of 5 is hard to determine who's on first.....are you adding more info or answering the dozens of questions already asked?

also...does your modem have wifi built in?

---

adding more info + answering the dozens of questions a

---

and your modem....dies it have a router wifi built in?

[azooz5005]

---

@Retired_Member wrote:

---

@azooz5005 wrote:

---

@Retired_Member wrote:

---

@azooz5005 wrote:

i dont understand ( did i just see doubles? )

my main modem is HG8245W5 and the Orbi for wifi only i put the cable in internet port "Yellow" ( not in ethernet )

---

@Retired_Member wrote:

did i just see doubles?

---

---

Message 3 of 5 is hard to determine who's on first.....are you adding more info or answering the dozens of questions already asked?

also...does your modem have wifi built in?

---

adding more info + answering the dozens of questions a

---

and your modem....dies it have a router wifi built in?

---

i think you mean does

yes i have but i disable it coz i want orbi wifi only

[FURRYe38]

https://carrier.huawei.com/en/products/fixed-network/access/cpe/k-series-products/HG8245W5

If this is your Modem/ONT, then it has a built in router and wifi. 

This would be a double NAT condition which isn't recommended. https://kb.netgear.com/30186/What-is-Double-NAT
https://kb.netgear.com/30187/How-to-fix-issues-with-Double-NAT
Couple of options,
1. Configure the modem for transparent bridge or modem only mode. Then use the Orbi router in router mode. You'll need to contact the ISP for help and information in regards to the modem being bridged correctly.
2. If you can't bridge the modem, disable ALL wifi radios on the modem, configure the modems DMZ/ExposedHost or IP Pass-Through for the IP address the Orbi router gets from the modem. Then you can use the Orbi router in Router mode.
3. Or disable all wifi radios on the modem and connect the Orbi router to the modem, configure AP mode on the Orbi router. https://kb.netgear.com/31218/How-do-I-configure-my-Orbi-router-to-act-as-an-access-point and https://www.youtube.com/watch?v=H7LOcJ8GdDo&app=desktop

I would try option #3...

[azooz5005]

---

@FURRYe38 wrote:

https://carrier.huawei.com/en/products/fixed-network/access/cpe/k-series-products/HG8245W5

If this is your Modem/ONT, then it has a built in router and wifi. 

This would be a double NAT condition which isn't recommended. https://kb.netgear.com/30186/What-is-Double-NAT
https://kb.netgear.com/30187/How-to-fix-issues-with-Double-NAT
Couple of options,
1. Configure the modem for transparent bridge or modem only mode. Then use the Orbi router in router mode. You'll need to contact the ISP for help and information in regards to the modem being bridged correctly.
2. If you can't bridge the modem, disable ALL wifi radios on the modem, configure the modems DMZ/ExposedHost or IP Pass-Through for the IP address the Orbi router gets from the modem. Then you can use the Orbi router in Router mode.
3. Or disable all wifi radios on the modem and connect the Orbi router to the modem, configure AP mode on the Orbi router. https://kb.netgear.com/31218/How-do-I-configure-my-Orbi-router-to-act-as-an-access-point and https://www.youtube.com/watch?v=H7LOcJ8GdDo&app=desktop

I would try option #3...

---

AP mode is allrady on

you can check my settings in link ( frist post )

how can i bridge modem ?

[FURRYe38]

Do a web search on you modem model or ask your ISP to help you bridge the modem

---

@azooz5005 wrote:

---

---

AP mode is allrady on

you can check my settings in link ( frist post )

how can i bridge modem ?

---

[azooz5005]

my modem is in the last update i can't make bridge ,  same problem

---

@FURRYe38 wrote:

Do a web search on you modem model or ask your ISP to help you bridge the modem

---

@azooz5005 wrote:

---

---

AP mode is allrady on

you can check my settings in link ( frist post )

how can i bridge modem ?

---

---

[FURRYe38]

Ok, I thought maybe it could be done. 

Is the Wifi fully disabed on the ISP modem? 

What is the distance between the router and satellite(s)?

Set 20/40Mhz Coexistence to 40Mhz only. Under Advanced Tab/Advanced Settings/Wireless Settings

Any Wifi Neighbors near by? If so, how many?

Use WiFi Sweet Spots to see the connect rate of your wifi devices while near the RBR first, then RBS. Power off the wifi radio for 5 seconds on the mobile device after moving near RBS. This ensures they connect to the nearest RBS. 

---

@azooz5005 wrote:

my modem is in the last update i can't make bridge ,  same problem

---

@FURRYe38 wrote:

Do a web search on you modem model or ask your ISP to help you bridge the modem

---

@azooz5005 wrote:

---

---

AP mode is allrady on

you can check my settings in link ( frist post )

how can i bridge modem ?

---

---

---

[azooz5005]

---

@FURRYe38 wrote:

Ok, I thought maybe it could be done. 

Is the Wifi fully disabed on the ISP modem? 

What is the distance between the router and satellite(s)?

Set 20/40Mhz Coexistence to 40Mhz only. Under Advanced Tab/Advanced Settings/Wireless Settings

Any Wifi Neighbors near by? If so, how many?

Use WiFi Sweet Spots to see the connect rate of your wifi devices while near the RBR first, then RBS. Power off the wifi radio for 5 seconds on the mobile device after moving near RBS. This ensures they connect to the nearest RBS. 

---

@azooz5005 wrote:

my modem is in the last update i can't make bridge ,  same problem

---

@FURRYe38 wrote:

Do a web search on you modem model or ask your ISP to help you bridge the modem

---

@azooz5005 wrote:

---

---

AP mode is allrady on

you can check my settings in link ( frist post )

how can i bridge modem ?

---

---

---

---

Ok, I thought maybe it could be done.

Is the Wifi fully disabed on the ISP modem?
-------Yes
What is the distance between the router and satellite(s)?
------- Mm 20m
Set 20/40Mhz Coexistence to 40Mhz only. Under Advanced Tab/Advanced Settings/Wireless Settings
-------I don’t understand but check my settings https://ibb.co/Sry7ZwD
Any Wifi Neighbors near by? If so, how many?
-------No

Use WiFi Sweet Spots to see the connect rate of your wifi devices while near the RBR first, then RBS. Power off the wifi radio for 5 seconds on the mobile device after moving near RBS. This ensures they connect to the nearest RBS.
Same prob

[FURRYe38]

---

@azooz5005 wrote:

Ok, I thought maybe it could be done.

Is the Wifi fully disabed on the ISP modem?
-------Yes
What is the distance between the router and satellite(s)?
------- Mm 20m
Set 20/40Mhz Coexistence to 40Mhz only. Under Advanced Tab/Advanced Settings/Wireless Settings
-------I don’t understand but check my settings https://ibb.co/Sry7ZwD 

Take the check mark out from the check box, select save or apply. 

Any Wifi Neighbors near by? If so, how many?
-------No

Use WiFi Sweet Spots to see the connect rate of your wifi devices while near the RBR first, then RBS. Power off the wifi radio for 5 seconds on the mobile device after moving near RBS. This ensures they connect to the nearest RBS.
Same prob 

What is the connection rates seen on the wifi device? Anything near 866Mbps or low rates while connected at the RBR? 

---

[azooz5005]

---

@FURRYe38 wrote:

---

@azooz5005 wrote:

Ok, I thought maybe it could be done.

Is the Wifi fully disabed on the ISP modem?
-------Yes
What is the distance between the router and satellite(s)?
------- Mm 20m
Set 20/40Mhz Coexistence to 40Mhz only. Under Advanced Tab/Advanced Settings/Wireless Settings
-------I don’t understand but check my settings https://ibb.co/Sry7ZwD 

Take the check mark out from the check box, select save or apply. 

Any Wifi Neighbors near by? If so, how many?
-------No

Use WiFi Sweet Spots to see the connect rate of your wifi devices while near the RBR first, then RBS. Power off the wifi radio for 5 seconds on the mobile device after moving near RBS. This ensures they connect to the nearest RBS.
Same prob 

What is the connection rates seen on the wifi device? Anything near 866Mbps or low rates while connected at the RBR? 

---

---

Take the check mark out from the check box, select save or apply. 

Witch check box ?

What is the connection rates seen on the wifi device? Anything near 866Mbps or low rates while connected at the RBR?

how can i know rates ? , i think less , coz i have 500mb ( this is my speed ) but Orbi give me 100 or 200 maximum 

[FURRYe38]

the 20/40Mhz Coexistence check box.

[azooz5005]

---

@FURRYe38 wrote:

the 20/40Mhz Coexistence check box.

---

done , same prob

[FURRYe38]

Downgrade FW on the RBR to v30 and factory reset the RBR and setup from scratch. Turn OFF the RBS. After you setup the RBR again after the downgrade test the connect rates. If there still low, youll need to make contact with NG support. 

[azooz5005]

---

@FURRYe38 wrote:

Downgrade FW on the RBR to v30 and factory reset the RBR and setup from scratch. Turn OFF the RBS. After you setup the RBR again after the downgrade test the connect rates. If there still low, youll need to make contact with NG support. 

---

Good idia , how can I downgrade it ? , where i can downlload FW ?

[FURRYe38]

https://www.netgear.com/support/

If your intereseted, you can try Voxel FW as well:

https://community.netgear.com/t5/Orbi/Voxels-FW-available-for-50-series-Orbi-only-available/m-p/1883...

You can always revert back to stock fw too.