Reply
dinokath
Star

WiFi with No Internet Connection After FW Update

Morning all,

 

SInce I updated the firmware to 2.5.1.16 from 2.5.1.8, I am having an issue with Wifi being connected but no internet being available. To compound the issue, I get the message of 'Connected No Internet' but still have an internet connection. This happens on both 2.4 and 5 bands.To solve the issue, I disconnect from WiFi and reconnect but this shouldn't be the fix.

 

As best I can tell, this happens only on WiFi. The laptop I am using to type this up is connected to the network via ethernet and I haven't experienced the issue here.My PS4 is also ethernet connected and while I was gaming last night, the TV kept throwing up 'No Internet Connection' messages dialog boxes but the online gaming was uniterrupted. 

 

I am technically inclined but I readily admit that when it comes to networks and their workings, it completely mystifies me. As far as I am concerned it's witchcraft. 

 

Thank you for any help you can provide. It is greatly appreciated! 

 

Some information on my setup:

ATT/Pace 5268AC Modem

  • DMZ+ mode set for the RBR50
  • IP address is distinct from RBR50
  • Both WiFi bands turned off

Orbi Settings

Internet Connection Status

IP Address 76.XXX.X.XXX - Same as modem
Subnet Mask 255.255.252.0 - Same as modem
Default Gateway 76.xxx.xxx.xxx - Same as modem
DHCP Server 172.xx.xx.xx - Modem's IP Address
DNS Server 8.8.8.8 and 8.8.4.4

Router Information

Hardware Version RBR50

Firmware Version V2.5.1.16

GUI Language Version V1.0.0.375

Operation Mode Router

LAN Port
MAC Address xx:xx:xx:xx:xx:xx
IP Address 192.168.1.1
DHCP Server On

Wireless Settings

2.4GHz Channel - 06

Enable WMM

CTSRTS Threshold 2347

Preamble Mode Automatic

Transmit Power 100%

5GHz Channel - 48

Same Advanced Settings as 2.4

Security - WPA2-PSK (AES)

Enable Daisy Chain Topography - Off - only 1 satellite is attached

Enable Implicit Beamforming - On

Enable MU-MIMO - On

Enable Fast Roaming - On

Internet Setup

No Login Required

Get UP Address from ISP dynamicall - ON

DNS Address - Set to Google DNS servers

MAC AddressUse Default Address

WAN Setup

Everything unchecked except Disable IGMP Proxying

MTU - 1500

NAT Filtering - Secured

LAN Setup

RIP Direction - Both

RIP Version - Disabled

Use Router as DHCP - checked

Advanced Settings 

In Router Mode

No Ports Forwarded or Triggered

No Dynamic DNS

No VPN

No Static Routes

No Remote Management

UPnP On - Seems my PS4's IP is listed there in UDP for ports 9308 and 3074

IPv6 - Auto Detect

  • Connection Type DHCP
  • Get DNS from ISP
  • LAN Setup Auto Config
  • IPv6 Filtering - Secured

 

 

 

 

 

Model: RBR50|Orbi AC3000 Tri-band WiFi Router
Message 1 of 21

Accepted Solutions
dinokath
Star

Re: WiFi with No Internet Connection After FW Update

Update as of this moment - installed Firefox (weird it wouldn't work with Chrome!) and was able to roll the firmware back on both the RBR and the RBS to the previous version, which is 2.5.1.8.

 

Did this around 1600 yesterday afternoon and as of 0930 this morning nothing has dropped the internet connection. Fingers crossed but I feel good that perhaps this did the trick because it would drop multiple times per hour, every hour, for the last couple weeks. Seemed to be the biggest problem on the Samsung S10E and my Androiud HiSense TV (maybe it is a conflict with the Android OS??) and now that I say that out loud, this happened on Android devices. Hmmm....

 

@BretD Noticed you are an admin on this forum. Perhaps you could pass along my experience with this firmware update to Netgear Support. Thanks!

View solution in original post

Message 16 of 21

All Replies
MuhammadAsif
Aspirant

Re: WiFi with No Internet Connection After FW Update

Recently I update the orbi firmware version & I noticed they have some bugs

1 major thing connected device not showing ?
Model: CBR40|Orbi AC2200 Tri-band WiFi Cable Modem Router
Message 2 of 21
FURRYe38
Guru

Re: WiFi with No Internet Connection After FW Update

Please try a factory reset and setup from scratch with the RBR and RBS.

Power OFF the ISP Modem for 30 seconds then back on. Walk thru the setup wizard on the RBR. 

 

 


@dinokath wrote:

Morning all,

 

SInce I updated the firmware to 2.5.1.16 from 2.5.1.8, I am having an issue with Wifi being connected but no internet being available. To compound the issue, I get the message of 'Connected No Internet' but still have an internet connection. This happens on both 2.4 and 5 bands.To solve the issue, I disconnect from WiFi and reconnect but this shouldn't be the fix.

 

As best I can tell, this happens only on WiFi. The laptop I am using to type this up is connected to the network via ethernet and I haven't experienced the issue here.My PS4 is also ethernet connected and while I was gaming last night, the TV kept throwing up 'No Internet Connection' messages dialog boxes but the online gaming was uniterrupted. 

 

I am technically inclined but I readily admit that when it comes to networks and their workings, it completely mystifies me. As far as I am concerned it's witchcraft. 

 

Thank you for any help you can provide. It is greatly appreciated! 

 

Some information on my setup:

ATT/Pace 5268AC Modem

  • DMZ+ mode set for the RBR50
  • IP address is distinct from RBR50
  • Both WiFi bands turned off

Orbi Settings

Internet Connection Status

IP Address 76.XXX.X.XXX - Same as modem
Subnet Mask 255.255.252.0 - Same as modem
Default Gateway 76.xxx.xxx.xxx - Same as modem
DHCP Server 172.xx.xx.xx - Modem's IP Address
DNS Server 8.8.8.8 and 8.8.4.4

Router Information

Hardware Version RBR50

Firmware Version V2.5.1.16

GUI Language Version V1.0.0.375

Operation Mode Router

LAN Port
MAC Address xx:xx:xx:xx:xx:xx
IP Address 192.168.1.1
DHCP Server On

Wireless Settings

2.4GHz Channel - 06

Enable WMM

CTSRTS Threshold 2347

Preamble Mode Automatic

Transmit Power 100%

5GHz Channel - 48

Same Advanced Settings as 2.4

Security - WPA2-PSK (AES)

Enable Daisy Chain Topography - Off - only 1 satellite is attached

Enable Implicit Beamforming - On

Enable MU-MIMO - On

Enable Fast Roaming - On

Internet Setup

No Login Required

Get UP Address from ISP dynamicall - ON

DNS Address - Set to Google DNS servers

MAC AddressUse Default Address

WAN Setup

Everything unchecked except Disable IGMP Proxying

MTU - 1500

NAT Filtering - Secured

LAN Setup

RIP Direction - Both

RIP Version - Disabled

Use Router as DHCP - checked

Advanced Settings 

In Router Mode

No Ports Forwarded or Triggered

No Dynamic DNS

No VPN

No Static Routes

No Remote Management

UPnP On - Seems my PS4's IP is listed there in UDP for ports 9308 and 3074

IPv6 - Auto Detect

  • Connection Type DHCP
  • Get DNS from ISP
  • LAN Setup Auto Config
  • IPv6 Filtering - Secured

 

 

 

 

 


 

My Setup (Cable 1Gbps/50Mbps)>CM1200 v2.02.03(LAG Disabled)>RBK853 v3.2.17.12
RBK50 v2.7.2.104(WW) Circle Enabled
Additional NG HW: C7800/CM1100/CAX80/CM2000, Orbi CBK40, R7800, R7960P, EX7500/EX7700, XR450 and WNHDE111
Message 3 of 21
dinokath
Star

Re: WiFi with No Internet Connection After FW Update

Sorry, should have said that I have done a factory reset


@FURRYe38 wrote:

Please try a factory reset and setup from scratch with the RBR and RBS.

Power OFF the ISP Modem for 30 seconds then back on. Walk thru the setup wizard on the RBR. 

 

 


@dinokath wrote:

Morning all,

 

SInce I updated the firmware to 2.5.1.16 from 2.5.1.8, I am having an issue with Wifi being connected but no internet being available. To compound the issue, I get the message of 'Connected No Internet' but still have an internet connection. This happens on both 2.4 and 5 bands.To solve the issue, I disconnect from WiFi and reconnect but this shouldn't be the fix.

 

As best I can tell, this happens only on WiFi. The laptop I am using to type this up is connected to the network via ethernet and I haven't experienced the issue here.My PS4 is also ethernet connected and while I was gaming last night, the TV kept throwing up 'No Internet Connection' messages dialog boxes but the online gaming was uniterrupted. 

 

I am technically inclined but I readily admit that when it comes to networks and their workings, it completely mystifies me. As far as I am concerned it's witchcraft. 

 

Thank you for any help you can provide. It is greatly appreciated! 

 

Some information on my setup:

ATT/Pace 5268AC Modem

  • DMZ+ mode set for the RBR50
  • IP address is distinct from RBR50
  • Both WiFi bands turned off

Orbi Settings

Internet Connection Status

IP Address 76.XXX.X.XXX - Same as modem
Subnet Mask 255.255.252.0 - Same as modem
Default Gateway 76.xxx.xxx.xxx - Same as modem
DHCP Server 172.xx.xx.xx - Modem's IP Address
DNS Server 8.8.8.8 and 8.8.4.4

Router Information

Hardware Version RBR50

Firmware Version V2.5.1.16

GUI Language Version V1.0.0.375

Operation Mode Router

LAN Port
MAC Address xx:xx:xx:xx:xx:xx
IP Address 192.168.1.1
DHCP Server On

Wireless Settings

2.4GHz Channel - 06

Enable WMM

CTSRTS Threshold 2347

Preamble Mode Automatic

Transmit Power 100%

5GHz Channel - 48

Same Advanced Settings as 2.4

Security - WPA2-PSK (AES)

Enable Daisy Chain Topography - Off - only 1 satellite is attached

Enable Implicit Beamforming - On

Enable MU-MIMO - On

Enable Fast Roaming - On

Internet Setup

No Login Required

Get UP Address from ISP dynamicall - ON

DNS Address - Set to Google DNS servers

MAC AddressUse Default Address

WAN Setup

Everything unchecked except Disable IGMP Proxying

MTU - 1500

NAT Filtering - Secured

LAN Setup

RIP Direction - Both

RIP Version - Disabled

Use Router as DHCP - checked

Advanced Settings 

In Router Mode

No Ports Forwarded or Triggered

No Dynamic DNS

No VPN

No Static Routes

No Remote Management

UPnP On - Seems my PS4's IP is listed there in UDP for ports 9308 and 3074

IPv6 - Auto Detect

  • Connection Type DHCP
  • Get DNS from ISP
  • LAN Setup Auto Config
  • IPv6 Filtering - Secured

 

 

 

 

 


 



on both the modem and the router. 

Message 4 of 21
FURRYe38
Guru

Re: WiFi with No Internet Connection After FW Update

So when walking thru the setup wizard on the RBR with a web browser, does it report any problems getting a connection with the modem? 

Did you get up a IP address reservation first for the RBR ON the modem so it's IP address doesn't change and then input this into the modems DMZ+? 

 

Try AP mode on the RBR and disable DMZ+ on the PACE modem. See if the RBR works in AP Mode with the PACE modem. Be sure the modems wifi is fully disabled. 

 

Seem others with various problems with the model modem. Most were resolved by upgrading to the Arris BGW-210 modem. 

My Setup (Cable 1Gbps/50Mbps)>CM1200 v2.02.03(LAG Disabled)>RBK853 v3.2.17.12
RBK50 v2.7.2.104(WW) Circle Enabled
Additional NG HW: C7800/CM1100/CAX80/CM2000, Orbi CBK40, R7800, R7960P, EX7500/EX7700, XR450 and WNHDE111
Message 5 of 21
dinokath
Star

Re: WiFi with No Internet Connection After FW Update

No, no issues reported when going through the setup, everything connects fine. Yes, the IP address is reserved on the modem's DMZ and doesn't change.

 

If I do the AP on the RBR, don't I lose the Netgear Armor and the firewall on the Orbi? 

 

If the problem is with the modem, why did it work just fine before the FW update? Tried to roll back the FW update and can do it on the satellite but the router keeps locking up the GUI and resetting the interface. 

Message 6 of 21
FURRYe38
Guru

Re: WiFi with No Internet Connection After FW Update

So the web page on the RBR reports no internet connection after the setup completes?

You don't need Armor or firewall in AP Mode as firewall is handled by the main host router up stream. 

 

What browser are you using to downgrade? Use IE11x32 or firefox.

You are using a wired PC to downgrade? Don't use a wireless connection for FW dowgrades. 

 

 

My Setup (Cable 1Gbps/50Mbps)>CM1200 v2.02.03(LAG Disabled)>RBK853 v3.2.17.12
RBK50 v2.7.2.104(WW) Circle Enabled
Additional NG HW: C7800/CM1100/CAX80/CM2000, Orbi CBK40, R7800, R7960P, EX7500/EX7700, XR450 and WNHDE111
Message 7 of 21
dinokath
Star

Re: WiFi with No Internet Connection After FW Update

The RBR reports internet works fine. It's the WiFi connected devices that report 'Connected but No Internet'. It is intermittent and seems to be isolated to the WIRELESS devices. The WIRED devices that are directly connected to the RBR via ethernet are working just fine

 

I get that the firewall on the 5268 works but I paid for Armor and like the interface and protection it affords and would rather it work as intended.

 

Using Chrome 83.0.4103.97. I'll download IE and Firefox and try as you suggest and report back.

Yes, using a PC directly wired into RBR to attempt the downgrade.

Message 8 of 21
FURRYe38
Guru

Re: WiFi with No Internet Connection After FW Update

What is the distance between the router and satellite(s)? 30 feet is recommended in between RBR and RBS to begin with depending upon building materials when wirelessly connected. https://kb.netgear.com/000036466/How-far-should-I-place-my-Orbi-satellite-from-my-Orbi-router

 

What channels are you using? Auto? Try setting manual channel 1, 6 or 11 on 2.4Ghz and any unused channel on 5Ghz.
Any Wifi Neighbors near by? If so, how many?

Try enabling Beamforming and MIMO(MIMO may or maynot be needed) and WMM. Under Advanced Tab/Advanced Settings/Wireless Settings

Try disabling the following and see:
Fast Roaming, IPv6 and Set 20/40Mhz Coexistence to 40Mhz only. Save settings and reboot the router and satellite(s).

 

The firewall the ISP modem needs to be disabled since the RBR is in router mode. Having two firewalls running is not good. Be sur the wifi radios on the modem are fully turned OFF. 

 

 

My Setup (Cable 1Gbps/50Mbps)>CM1200 v2.02.03(LAG Disabled)>RBK853 v3.2.17.12
RBK50 v2.7.2.104(WW) Circle Enabled
Additional NG HW: C7800/CM1100/CAX80/CM2000, Orbi CBK40, R7800, R7960P, EX7500/EX7700, XR450 and WNHDE111
Message 9 of 21
dinokath
Star

Re: WiFi with No Internet Connection After FW Update


@FURRYe38 wrote:

It's been running for 2 years just fine. But, it's around 30 feet, yes. What is the distance between the router and satellite(s)? 30 feet is recommended in between RBR and RBS to begin with depending upon building materials when wirelessly connected. https://kb.netgear.com/000036466/How-far-should-I-place-my-Orbi-satellite-from-my-Orbi-router

 

All this is in the post above. Again, it was working great up until recently.What channels are you using? Auto? Try setting manual channel 1, 6 or 11 on 2.4Ghz and any unused channel on 5Ghz.
Any Wifi Neighbors near by? If so, how many? Yes, I live in a neighborhood and can see 3 - 4 other networks when looking. I have been diligent to make sure our channels do not overlap.

Try enabling Beamforming and MIMO(MIMO may or maynot be needed) and WMM. Under Advanced Tab/Advanced Settings/Wireless Settings. Tried that several times and in every variation over the last two weeks. Still cannot get it stable.,

Try disabling the following and see:
Fast Roaming, IPv6 and Set 20/40Mhz Coexistence to 40Mhz only. Save settings and reboot the router and satellite(s).Yep, been there, done this.

 

The firewall the ISP modem needs to be disabled since the RBR is in router mode. Having two firewalls running is not good. Be sur the wifi radios on the modem are fully turned OFF. Yes, firewall is disabled due to the DMZ+ setting and yes, the radios are off on the 5268

 

 


 

Message 10 of 21
FURRYe38
Guru

Re: WiFi with No Internet Connection After FW Update

I would try AP mode with the DMZ disabled on the modem. 

One last thing would be to factory reset and not enable Armor to see if Armor maybe causing problems. Armor has been known to cause some problems. 

 

Contact NG support for additional help and information as well. 

My Setup (Cable 1Gbps/50Mbps)>CM1200 v2.02.03(LAG Disabled)>RBK853 v3.2.17.12
RBK50 v2.7.2.104(WW) Circle Enabled
Additional NG HW: C7800/CM1100/CAX80/CM2000, Orbi CBK40, R7800, R7960P, EX7500/EX7700, XR450 and WNHDE111
Message 11 of 21
dinokath
Star

Re: WiFi with No Internet Connection After FW Update

Thanks for the effort. I appreciate it. This thing is driving me crazy...

Message 12 of 21
FURRYe38
Guru

Re: WiFi with No Internet Connection After FW Update

Understand man. Orbi can be probmatic for sure. 

 

As last restore, You can try Voxels FW for Orbi:
https://community.netgear.com/t5/Orbi/Voxels-FW-available-for-50-series-Orbi-only-available/m-p/1883...
You can revert back to stock FW if it doesn't work out for you. 

My Setup (Cable 1Gbps/50Mbps)>CM1200 v2.02.03(LAG Disabled)>RBK853 v3.2.17.12
RBK50 v2.7.2.104(WW) Circle Enabled
Additional NG HW: C7800/CM1100/CAX80/CM2000, Orbi CBK40, R7800, R7960P, EX7500/EX7700, XR450 and WNHDE111
Message 13 of 21
JaGresh74
Aspirant

Re: WiFi with No Internet Connection After FW Update

Having exactly the same issues. Tends to drop on WiFi about 11pm each night for almost passed week. We as only when I jumped on an IPAD there was a notification on ORBI app that my firmware updated to 2.5.1.16, six days ago which is about right.

 

I think this update has caused my issues. It's been great to date and should be for money I paid for the kit.

 

I've not yet tried a factory reset but sounds like didn't help you?

 

John


@dinokath wrote:

Morning all,

 

SInce I updated the firmware to 2.5.1.16 from 2.5.1.8, I am having an issue with Wifi being connected but no internet being available. To compound the issue, I get the message of 'Connected No Internet' but still have an internet connection. This happens on both 2.4 and 5 bands.To solve the issue, I disconnect from WiFi and reconnect but this shouldn't be the fix.

 

As best I can tell, this happens only on WiFi. The laptop I am using to type this up is connected to the network via ethernet and I haven't experienced the issue here.My PS4 is also ethernet connected and while I was gaming last night, the TV kept throwing up 'No Internet Connection' messages dialog boxes but the online gaming was uniterrupted. 

 

I am technically inclined but I readily admit that when it comes to networks and their workings, it completely mystifies me. As far as I am concerned it's witchcraft. 

 

Thank you for any help you can provide. It is greatly appreciated! 

 

Some information on my setup:

ATT/Pace 5268AC Modem

  • DMZ+ mode set for the RBR50
  • IP address is distinct from RBR50
  • Both WiFi bands turned off

Orbi Settings

Internet Connection Status

IP Address 76.XXX.X.XXX - Same as modem
Subnet Mask 255.255.252.0 - Same as modem
Default Gateway 76.xxx.xxx.xxx - Same as modem
DHCP Server 172.xx.xx.xx - Modem's IP Address
DNS Server 8.8.8.8 and 8.8.4.4

Router Information

Hardware Version RBR50

Firmware Version V2.5.1.16

GUI Language Version V1.0.0.375

Operation Mode Router

LAN Port
MAC Address xx:xx:xx:xx:xx:xx
IP Address 192.168.1.1
DHCP Server On

Wireless Settings

2.4GHz Channel - 06

Enable WMM

CTSRTS Threshold 2347

Preamble Mode Automatic

Transmit Power 100%

5GHz Channel - 48

Same Advanced Settings as 2.4

Security - WPA2-PSK (AES)

Enable Daisy Chain Topography - Off - only 1 satellite is attached

Enable Implicit Beamforming - On

Enable MU-MIMO - On

Enable Fast Roaming - On

Internet Setup

No Login Required

Get UP Address from ISP dynamicall - ON

DNS Address - Set to Google DNS servers

MAC AddressUse Default Address

WAN Setup

Everything unchecked except Disable IGMP Proxying

MTU - 1500

NAT Filtering - Secured

LAN Setup

RIP Direction - Both

RIP Version - Disabled

Use Router as DHCP - checked

Advanced Settings 

In Router Mode

No Ports Forwarded or Triggered

No Dynamic DNS

No VPN

No Static Routes

No Remote Management

UPnP On - Seems my PS4's IP is listed there in UDP for ports 9308 and 3074

IPv6 - Auto Detect

  • Connection Type DHCP
  • Get DNS from ISP
  • LAN Setup Auto Config
  • IPv6 Filtering - Secured

 

 

 

 

 


 

Message 14 of 21
FURRYe38
Guru

Re: WiFi with No Internet Connection After FW Update

What is the Mfr and model# of the Internet Service Providers modem/ONT the NG router is connected too?

Any Wifi Neighbors near by? If so, how many?

 

Is Armor or Circle enabled on your system? 

 

Please try a reset on yours....


@JaGresh74 wrote:

Having exactly the same issues. Tends to drop on WiFi about 11pm each night for almost passed week. We as only when I jumped on an IPAD there was a notification on ORBI app that my firmware updated to 2.5.1.16, six days ago which is about right.

 

I think this update has caused my issues. It's been great to date and should be for money I paid for the kit.

 

I've not yet tried a factory reset but sounds like didn't help you?

 

My Setup (Cable 1Gbps/50Mbps)>CM1200 v2.02.03(LAG Disabled)>RBK853 v3.2.17.12
RBK50 v2.7.2.104(WW) Circle Enabled
Additional NG HW: C7800/CM1100/CAX80/CM2000, Orbi CBK40, R7800, R7960P, EX7500/EX7700, XR450 and WNHDE111
Message 15 of 21
dinokath
Star

Re: WiFi with No Internet Connection After FW Update

Update as of this moment - installed Firefox (weird it wouldn't work with Chrome!) and was able to roll the firmware back on both the RBR and the RBS to the previous version, which is 2.5.1.8.

 

Did this around 1600 yesterday afternoon and as of 0930 this morning nothing has dropped the internet connection. Fingers crossed but I feel good that perhaps this did the trick because it would drop multiple times per hour, every hour, for the last couple weeks. Seemed to be the biggest problem on the Samsung S10E and my Androiud HiSense TV (maybe it is a conflict with the Android OS??) and now that I say that out loud, this happened on Android devices. Hmmm....

 

@BretD Noticed you are an admin on this forum. Perhaps you could pass along my experience with this firmware update to Netgear Support. Thanks!

View solution in original post

Message 16 of 21
FURRYe38
Guru

Re: WiFi with No Internet Connection After FW Update

I avoid chrome for doing any FW updates. 

 

Wonder why some users are having difficulty with this version of FW, even after a reset and others are not.

@Blanca_O 

@Christian_R 

My Setup (Cable 1Gbps/50Mbps)>CM1200 v2.02.03(LAG Disabled)>RBK853 v3.2.17.12
RBK50 v2.7.2.104(WW) Circle Enabled
Additional NG HW: C7800/CM1100/CAX80/CM2000, Orbi CBK40, R7800, R7960P, EX7500/EX7700, XR450 and WNHDE111
Message 17 of 21
dinokath
Star

Re: WiFi with No Internet Connection After FW Update

Update - The rollback of the firmware continues to provide stability and has solved the problem I was encountering. Unless something changes, I will not report back. Thanks again for the help!

Message 18 of 21
FURRYe38
Guru

Re: WiFi with No Internet Connection After FW Update

Glad reverting back helped. 

Next time, try manually loading FW by downloading the FW files and applying them manually. Factory reset and setup from scratch. Next time. 

 

Please mark your thread as solved so others will know. 

 

Enjoy. Smiley Wink

My Setup (Cable 1Gbps/50Mbps)>CM1200 v2.02.03(LAG Disabled)>RBK853 v3.2.17.12
RBK50 v2.7.2.104(WW) Circle Enabled
Additional NG HW: C7800/CM1100/CAX80/CM2000, Orbi CBK40, R7800, R7960P, EX7500/EX7700, XR450 and WNHDE111
Message 19 of 21
dinokath
Star

Re: WiFi with No Internet Connection After FW Update

Just another follow up. Still no issues since rolling back the firmware. 

Message 20 of 21
FURRYe38
Guru

Re: WiFi with No Internet Connection After FW Update

Enjoy. Smiley Wink

My Setup (Cable 1Gbps/50Mbps)>CM1200 v2.02.03(LAG Disabled)>RBK853 v3.2.17.12
RBK50 v2.7.2.104(WW) Circle Enabled
Additional NG HW: C7800/CM1100/CAX80/CM2000, Orbi CBK40, R7800, R7960P, EX7500/EX7700, XR450 and WNHDE111
Message 21 of 21
Top Contributors
Discussion stats
  • 20 replies
  • 1449 views
  • 3 kudos
  • 4 in conversation
Announcements