Reply
chouchou7
Aspirant

auto sensing Ethernet port?

Hello,

 I setup the orbi with wired backhaul so I use one port to connect with  the orbi router. But after I connect my device(PC) to the other port, the whole orbi system is down. I cannot get online anymore. So I wander if the two ports are auto sensing?

Model: RBR20|Orbi AC2200 Tri-band WiFi Router
Message 1 of 6

Accepted Solutions
FURRYe38
Guru

Re: auto sensing Ethernet port?

They are...

 

What Firmware is currently loaded?
What is the Mfr and model# of the ISP modem the NG router is connected too?
Is the Orbi system operating in Router or AP mode?
What is the Mfr and model# of the ethernet switch if one is in the configuration.

 

Ensure the cable between the RBR and PC is of good working quality. CAT6 is recommended. Swap cables for testing. 

Try different ports. 

Try a different PC. 

 

Are you connecting to the RBR or RBS? 

 

Disable Daisy Chain if you have the RBS connected ethernet to the RBR. 

 

My Setup (Cable 1Gbps/50Mbps)>CM1200 v2.02.03(LAG Disabled)>RBK853 v3.2.17.12
RBK50 v2.7.2.104(WW) Circle Enabled
Additional NG HW: C7800/CM1100/CAX80/CM2000, Orbi CBK40, R7800, R7960P, EX7500/EX7700, XR450 and WNHDE111

View solution in original post

Message 2 of 6

All Replies
FURRYe38
Guru

Re: auto sensing Ethernet port?

They are...

 

What Firmware is currently loaded?
What is the Mfr and model# of the ISP modem the NG router is connected too?
Is the Orbi system operating in Router or AP mode?
What is the Mfr and model# of the ethernet switch if one is in the configuration.

 

Ensure the cable between the RBR and PC is of good working quality. CAT6 is recommended. Swap cables for testing. 

Try different ports. 

Try a different PC. 

 

Are you connecting to the RBR or RBS? 

 

Disable Daisy Chain if you have the RBS connected ethernet to the RBR. 

 

My Setup (Cable 1Gbps/50Mbps)>CM1200 v2.02.03(LAG Disabled)>RBK853 v3.2.17.12
RBK50 v2.7.2.104(WW) Circle Enabled
Additional NG HW: C7800/CM1100/CAX80/CM2000, Orbi CBK40, R7800, R7960P, EX7500/EX7700, XR450 and WNHDE111

View solution in original post

Message 2 of 6
chouchou7
Aspirant

Re: auto sensing Ethernet port?

Thank you, please see my setup below

 

What Firmware is currently loaded? Latest 2.3.5.26
What is the Mfr and model# of the ISP modem the NG router is connected too? Netgear CM500
Is the Orbi system operating in Router or AP mode? Router
What is the Mfr and model# of the ethernet switch if one is in the configuration. Netgear GS308P

 

Ensure the cable between the RBR and PC is of good working quality. CAT6 is recommended. Swap cables for testing. OK

Try different ports. 

Try a different PC. 

 

Are you connecting to the RBR or RBS? RBS, RBR connected to the switch, and RBS connected to the switch

 

Disable Daisy Chain if you have the RBS connected ethernet to the RBR. Will do

 

Message 3 of 6
FURRYe38
Guru

Re: auto sensing Ethernet port?

Try connecting to the RBR with out the switch in the mix. 

My Setup (Cable 1Gbps/50Mbps)>CM1200 v2.02.03(LAG Disabled)>RBK853 v3.2.17.12
RBK50 v2.7.2.104(WW) Circle Enabled
Additional NG HW: C7800/CM1100/CAX80/CM2000, Orbi CBK40, R7800, R7960P, EX7500/EX7700, XR450 and WNHDE111
Message 4 of 6
chouchou7
Aspirant

Re: auto sensing Ethernet port?

disabled Daisy Chain and it worked very well! Thank you!

Message 5 of 6
FURRYe38
Guru

Re: auto sensing Ethernet port?

Enjoy. Smiley Wink

My Setup (Cable 1Gbps/50Mbps)>CM1200 v2.02.03(LAG Disabled)>RBK853 v3.2.17.12
RBK50 v2.7.2.104(WW) Circle Enabled
Additional NG HW: C7800/CM1100/CAX80/CM2000, Orbi CBK40, R7800, R7960P, EX7500/EX7700, XR450 and WNHDE111
Message 6 of 6
Top Contributors
Discussion stats
  • 5 replies
  • 883 views
  • 1 kudo
  • 2 in conversation
Announcements