- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
Connect 10TB USB drive to ReadyNAS 3138
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
I have an external USB drive w/ 10TB as of now formatted with ExFat.
It does not show up in the frontend (System page) of my ReadyNAS 3138.
dmesg shows this:
[ 3959.665535] usb 1-1.1: new high-speed USB device number 4 using ehci-pci
[ 3959.832285] usb-storage 1-1.1:1.0: USB Mass Storage device detected
[ 3959.832414] scsi host11: usb-storage 1-1.1:1.0
[ 3960.834519] scsi 11:0:0:0: Direct-Access Seagate Expansion HDD 1801 PQ: 0 ANSI: 6
[ 3960.835322] sd 11:0:0:0: Attached scsi generic sg4 type 0
[ 3979.695568] sd 11:0:0:0: [sde] Very big device. Trying to use READ CAPACITY(16).
[ 3979.696058] sd 11:0:0:0: [sde] 19532873727 512-byte logical blocks: (10.0 TB/9.09 TiB)
[ 3979.696063] sd 11:0:0:0: [sde] 4096-byte physical blocks
[ 3979.697160] sd 11:0:0:0: [sde] Write Protect is off
[ 3979.697167] sd 11:0:0:0: [sde] Mode Sense: 47 00 00 08
[ 3979.698198] sd 11:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3979.699707] sd 11:0:0:0: [sde] Very big device. Trying to use READ CAPACITY(16).
[ 3979.767812] sde: sde1 sde2
[ 3979.769307] sd 11:0:0:0: [sde] Very big device. Trying to use READ CAPACITY(16).
[ 3979.771691] sd 11:0:0:0: [sde] Attached SCSI disk
[ 3981.607617] nfsd: last server has exited, flushing export cache
[ 3981.649436] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 3981.649464] NFSD: starting 90-second grace period (net ffffffff88d782c0)
In the backup howto it is stated that the preferred format is ext4. The notes at the bottom say that one should try NTFS or FAT32 if the disk is not showing up.
Since this is a brand new disk I would like to make sure that I can use it with my NAS as I otherwise may still return it.
So my questions are:
- Can this disk be used?
- Which format shall I use?
- How shall I format it, can I use a command line directly on the NAS?
(see dmesg info above)
Thanks a lot in advance.
Solved! Go to Solution.
Accepted Solutions
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
The ReadyNAS does not natively support EXFAT, but I understand you can install exfat-fuse and exfat-utils via SSH. Since my backup is to other NAS, I've not tried it myself.
All Replies
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Connect 10TB USB drive to ReadyNAS 3138
@loco42 wrote:In the backup howto it is stated that the preferred format is ext4.
Personally I disagree with that advice for backup. If your PCs can't read the backup, then it isn't worth much. So I recommend choosing a format you can read on your other PCs. NTFS can be read and written by Windows, and read by Mac.
@loco42 wrote:
How shall I format it, can I use a command line directly on the NAS?
If you have a Windows PC, I would format it there. I'd start by going into the windows disk manager, and delete any partitions that are on the drive. Then create a new one, and initialize it. Format using NTFS (as noted above).
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
The ReadyNAS does not natively support EXFAT, but I understand you can install exfat-fuse and exfat-utils via SSH. Since my backup is to other NAS, I've not tried it myself.