- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
Re: Firmware Update 6.7.3 -> 6.7.4 OK
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Firmware Update 6.7.3 -> 6.7.4 OK
For the record, I have just updated 6.7.3 -> 6.7.4 and all is fine and well. I know a bit of positive reinforcement is always welcome from the devs and fellow users alike, especially in light of the 'fun' I had earlier in the week with 6.7.1 -> 6.7.3 ; ).
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Firmware Update 6.7.3 -> 6.7.4 OK
Likewise here! It went smoothly.Thanks NETGEAR!
Is there anybody who turned AV on yet on an ARM device?
I. Konuk
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Firmware Update 6.7.3 -> 6.7.4 OK
Hi everyone.
Just upgraded the firmware to 6.7.4 and was wondering how stable this version was, or if anyone is having the same issues I am experiencing?
- mediaservers (both Netgear and Nero MediaHome) are no longer working;
- the admin pages are noticably slower;
- cloud page under Admin fails to load and logs me out;
These are the things experienced so far.
Was wondering if anyone else was having the same issues?
Running RN104.
Greg
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Firmware Update 6.7.3 -> 6.7.4 OK
Greg_M send in your logs (see the Sending Logs link in my sig).
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Firmware Update 6.7.3 -> 6.7.4 OK
Hello.
Just sent it to you now.
Thanks for looking into this for me.
Regards
Greg
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Firmware Update 6.7.3 -> 6.7.4 OK
Greg_M the logs show that you updated from 6.6.1 to 6.7.4.
I can see your system was OOMing (running Out of Memory). This may suggest that you're running quite a bit on this system.
In meminfo.log I can see
SwapTotal: 523708 kB
SwapFree: 150352 kB
So you're using most of the swap space.
You could try disabling quotas on the data volume if you haven't already and see if this helps.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Firmware Update 6.7.3 -> 6.7.4 OK
Just following on this thread, I updated both my 104 & 316 systems to 6.7.4 and the installation went very well with no issues.
The 316 was on 6.7.1 and the 104 was on 6.7.3 prior to the updates.
I have also started using AntiVirus again on my 104 after about 3-4 months and after the initial update and about 15 mins of disk activity everything seems to have settled down.
Hope this helps.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: Firmware Update 6.7.3 -> 6.7.4 OK
Thank you.
Apart from re-installing Nero, the drive now seems to be behaving like it used to.
Quotas were already disabled.
Out of interest, I downloaded the logs again and shows the following:
SwapTotal: 523708 kB
SwapFree: 323300 kB
Is this more 'normal?'
Thank you for your assistance. Very much appreciated.
Greg