- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
Re: RN102 - Rebuilding after disc change - md1 on 1 drive only
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello,
after hdd change in RN102 Unit (FW 6.9.3, 2x WD RED 2TB) Nas says all is OK.
But when i look in PHPsysinfo i see this:
md127 RAID1 (2 disc) - OK
md0 RAID1 (2 disc) - OK
md1 RAID1 (1disc) ??? this volume is on old disc only (sdb2)
Additional Information Status active RAID-Level raid1 Persistent Superblock available Registered/Active Disks
Is there anything i need to do to corect this state of md1?
How to get expand on new disc? Or can I ignore this state?
Can anyone tell me what to do?
Thank you very much.
Solved! Go to Solution.
Accepted Solutions
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
All Replies
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: RN102 - Rebuilding after disc change - md1 on 1 drive only
MD1 is the swap partition, so I don't think it's all that critical.
Hopefully @mdgm-ntgr will chime in.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: RN102 - Rebuilding after disc change - md1 on 1 drive only
This should be easy to fix via SSH.
You'd need to start by checking a few things
# cat /proc/partitions
# cat /proc/mdstat
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: RN102 - Rebuilding after disc change - md1 on 1 drive only
Thanks @mdgm-ntgr
# cat /proc/partitions
31 0 1536 mtdblock0 31 1 512 mtdblock1 31 2 6144 mtdblock2 31 3 4096 mtdblock3 31 4 118784 mtdblock4 8 0 1953514584 sda 8 1 4194304 sda1 8 3 1948793912 sda3 8 16 1953514584 sdb 8 17 4194304 sdb1 8 18 524288 sdb2 8 19 1948793912 sdb3 9 0 4190208 md0 9 1 523712 md1 9 127 1948662784 md127
cat /proc/mdstat
Personalities : [raid0] [raid1] [raid10] [raid6] [raid5] [raid4] md127 : active raid1 sda3[2] sdb3[1] 1948662784 blocks super 1.2 [2/2] [UU] md1 : active raid1 sdb2[0] 523712 blocks super 1.2 [1/1] [U] md0 : active raid1 sda1[2] sdb1[1] 4190208 blocks super 1.2 [2/2] [UU] unused devices: <none>
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: RN102 - Rebuilding after disc change - md1 on 1 drive only
There's no sda2, so for some reason the partition for swap wasn't created.
Did you try a reboot?
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: RN102 - Rebuilding after disc change - md1 on 1 drive only
I tried several times. No change. I sended you PM
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: RN102 - Rebuilding after disc change - md1 on 1 drive only
All OK now. Thank you verry much for your help.