× NETGEAR will be terminating ReadyCLOUD service by July 1st, 2023. For more details click here.
Orbi WiFi 7 RBE973
Reply

RN10200 not visible

sanjeewakuku
Aspirant

RN10200 not visible

hi,

power LED on.

strat up blink few second only.

network port green color LED blinking. 

 but no ip or discover to RAIDar

how to pix that 

 

szdfghj.jpg

Model: RN10200|ReadyNAS 100 Series 2- Bay (Diskless)
Message 1 of 17

Accepted Solutions
sanjeewakuku
Aspirant

Re: RN10200 not visible

i have using usbrecovery.v2.0.T14.support.  USB flash and problem solved

View solution in original post

Message 17 of 17

All Replies
StephenB
Guru

Re: RN10200 not visible

Is this a new system setup?

 

Are there disks installed in the RN102?

Message 2 of 17
sanjeewakuku
Aspirant

Re: RN10200 not visible


@StephenB wrote:

Is this a new system setup?

 

Are there disks installed in the RN102?


no. i have take ip image from my router. 

no didn't install disk

Message 3 of 17
msq
Apprentice
Apprentice

Re: RN10200 not visible


@sanjeewakuku wrote:

@StephenB wrote:

Is this a new system setup?

 

Are there disks installed in the RN102?


no. i have take ip image from my router. 

no didn't install disk


I think it will not pick up IP address unless there is at least one disk inserted.

Message 4 of 17
sanjeewakuku
Aspirant

Re: RN10200 not visible



 


I think it will not pick up IP address unless there is at least one disk inserted.

 

 

i think OS not boot. i have plug the power after power LED blink few second and LED stable on.  can i get advice how to install OS using USB flash drive

Message 5 of 17
msq
Apprentice
Apprentice

Re: RN10200 not visible

Please try the following:

 

- power off the device

- inster one clean drive

- boot it again

- check on your router or RAIDar what is the IP of this router

Message 6 of 17
sanjeewakuku
Aspirant

Re: RN10200 not visible


@msq wrote:

Please try the following:

 

- power off the device

- inster one clean drive

- boot it again

- check on your router or RAIDar what is the IP of this router


dne. same issue. not change. RAIDar could not find any NETGEAR storage on your network. on RAIDar

Message 7 of 17
msq
Apprentice
Apprentice

Re: RN10200 not visible

If that is the device you're trying to set up for the first time - you can try to reset it.

 

Additionally - is your router running dhcp? Or device is booted with its default IP address but your own IP settings are not allowing to see your ReadyNAS?

Message 8 of 17
sanjeewakuku
Aspirant

Re: RN10200 not visible


@msq wrote:

If that is the device you're trying to set up for the first time - you can try to reset it.

 

Additionally - is your router running dhcp? Or device is booted with its default IP address but your own IP settings are not allowing to see your ReadyNAS?


no. alredy running correctly. one time upgrade and will never geting up. maybe 1 yrar later that happend. i think somthing wrong with OS.  Yes. my router running DHCP. i have 

1.Power off your storage system.
2.Using a straightened paper clip, press and hold the Reset button.
3.Press the Power button.
The system powers on.
4.Continue to press the Reset button until the Power button LED, USB and backup status LED, disk 1 LED, and disk 2 LED light.
5.Press the Backup button to scroll through boot mode options.

 

 

Factory default.

same result. divice not visible for me. 😞

Message 9 of 17
msq
Apprentice
Apprentice

Re: RN10200 not visible

Ok - factory default already erased all data on the disk....

 

You can try OS reinstall - this is next step after 'factory default'.

Message 10 of 17
sanjeewakuku
Aspirant

Re: RN10200 not visible


@msq wrote:

Ok - factory default already erased all data on the disk....

 

You can try OS reinstall - this is next step after 'factory default'.


power off and press reset button and plug to power after slelct boot menu OS reinstall
Disk 2 LED lights. and press reset button.

result> power LED blink few seconds and LED stable.

not visibel yet. 😞

Message 11 of 17
msq
Apprentice
Apprentice

Re: RN10200 not visible

Both - factory reset and os reinstall can take 5 to 15 minutes. Additionally:

Factory default. Initiates a short disk test that takes approximately 5 minutes. After the disk test, a 10-minute time-out period begins, during which all LEDs blink simultaneously.

 

Please - give it few more minutes.

 

Message 12 of 17
sanjeewakuku
Aspirant

Re: RN10200 not visible


@msq wrote:

Both - factory reset and os reinstall can take 5 to 15 minutes. Additionally:

Factory default. Initiates a short disk test that takes approximately 5 minutes. After the disk test, a 10-minute time-out period begins, during which all LEDs blink simultaneously.

 

Please - give it few more minutes.

 

ok now again OS reinstall
select Disk 2 LED light and reset button. 

power LED blink few second and continues LED on now. im waiting 15 min. and i will post reply whats happend. 


 

Message 13 of 17
sanjeewakuku
Aspirant

Re: RN10200 not visible

not change. same issue. 😞 😞  RN10200 not visible 

Message 14 of 17
JohnCM_S
NETGEAR Employee Retired

Re: RN10200 not visible

Hi sanjeewakuku,

 

Do you have RAIDar installed on a computer? If yes, does RAIDar detect the NAS even if there is no disk inside it?

 

Regards,
JohnCM_S
NETGEAR Community Team

Message 15 of 17
JohnCM_S
NETGEAR Employee Retired

Re: RN10200 not visible

Hi sanjeewakuku,


We’d greatly appreciate hearing your feedback letting us know if the information we provided has helped resolve your issue or if you need further assistance.

If your issue is now resolved, we encourage you to mark the appropriate reply as the “Accept as Solution” or post what resolved it and mark it as solution so others can be confident in benefiting from the solution.
 
The Netgear community looks forward to hearing from you and being a helpful resource in the future!
 
Regards,

JohnCM_S
NETGEAR Community Team

Message 16 of 17
sanjeewakuku
Aspirant

Re: RN10200 not visible

i have using usbrecovery.v2.0.T14.support.  USB flash and problem solved

Message 17 of 17
Top Contributors
Discussion stats
  • 16 replies
  • 4431 views
  • 6 kudos
  • 4 in conversation
Announcements