× NETGEAR will be terminating ReadyCLOUD service by July 1st, 2023. For more details click here.
Orbi WiFi 7 RBE973
Reply

Re: ReadyNAS BusinessPro (6310) upgrade to OS 6 stuck at Booting 98%

Blues11
Luminary

ReadyNAS BusinessPro (6310) upgrade to OS 6 stuck at Booting 98%

Subject pretty much says it all. It's been stuck at "Booting 98%" for more than eight hours.

 

I've read other posts saying that this upgrade was successful. For those who had success, how long did it take?

 

Thanks.

Message 1 of 8

Accepted Solutions
mdgm-ntgr
NETGEAR Employee Retired

Re: ReadyNAS BusinessPro (6310) upgrade to OS 6 stuck at Booting 98%

Did you install the Prep add-on before installing the R4toR6 bin?

If not you will need to do a manual factory default via the boot menu

If you did install the Prep add-on at this point you could try doing a manual factory default via the boot menu anyway.

If it still won't come up then I can take a look.

View solution in original post

Message 6 of 8

All Replies
mdgm-ntgr
NETGEAR Employee Retired

Re: ReadyNAS BusinessPro (6310) upgrade to OS 6 stuck at Booting 98%

Can you try powering off the system and then booting it again?

 

If that does not resolving it perhaps try a factory reset (wipes all data, settings, everything) using the boot menu.

Message 2 of 8
Blues11
Luminary

Re: ReadyNAS BusinessPro (6310) upgrade to OS 6 stuck at Booting 98%

OK. I just pressed the on-off button briefly and the display changed to "systemd-quotacheck". Then I pressed it briefly again and it again displayed "Booting 98%."

 

Should I simply hold it down until it shuts off and then turn it on again?

 

Message 3 of 8
mdgm-ntgr
NETGEAR Employee Retired

Re: ReadyNAS BusinessPro (6310) upgrade to OS 6 stuck at Booting 98%

Yes.

I assume that as you are updating from OS4 to OS6 you have backed up your data.

Message 4 of 8
Blues11
Luminary

Re: ReadyNAS BusinessPro (6310) upgrade to OS 6 stuck at Booting 98%

Yeah. I expected to have to reload (re-backup) all the data from the 516. So, I just rebooted.

 

It says "Booting..." It went to 90% in less than a minute and then to 92% a minute later. Now, thirty minutes later, it still says 92%. What do you suggest I do next?

Message 5 of 8
mdgm-ntgr
NETGEAR Employee Retired

Re: ReadyNAS BusinessPro (6310) upgrade to OS 6 stuck at Booting 98%

Did you install the Prep add-on before installing the R4toR6 bin?

If not you will need to do a manual factory default via the boot menu

If you did install the Prep add-on at this point you could try doing a manual factory default via the boot menu anyway.

If it still won't come up then I can take a look.

Message 6 of 8
Blues11
Luminary

Re: ReadyNAS BusinessPro (6310) upgrade to OS 6 stuck at Booting 98%

It seems it just needed a push. I shut it off and then brought up the boot system menu. I selected Factory Restore. After a relatively short amount of time (minutes), the system came up and I was able to get to it via RAIDar. And it's running OS 6.6.0.

 

Note to anyone else who does this with an older unit. The old documentation for the ReadyNAS Business Pro says the default userID/Password combination is admin/netgear1. But if you upgrade to OS6, it's admin/password.

 

Thank you so much for your help.

Message 7 of 8
mdgm-ntgr
NETGEAR Employee Retired

Re: ReadyNAS BusinessPro (6310) upgrade to OS 6 stuck at Booting 98%

Yes, if you are running OS6 you have to use the OS6 credentials like you would with any other box running OS6. Future firmware updates are done the normal way on OS6. You would install them just the same way as you would on your 516.

The special image is only needed for the conversion to OS6.

Message 8 of 8
Top Contributors
Discussion stats
  • 7 replies
  • 3595 views
  • 0 kudos
  • 2 in conversation
Announcements